NEC Neax2000 Ivs Isdn System Manual
Have a look at the manual NEC Neax2000 Ivs Isdn System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ND-45857 (E) CHAPTER 4 Page 89 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA • YY = 33 (Interval of ringing signal) (1) Trunk Route No. (00 – 63) (2) 0: 0.4s ON – 0.2s OFF – 0.4s ON–2s OFF 1: 0.4s ON – 0.2s OFF – 0.4s ON–2s OFF 2: 1s ON – 2s OFF 3 : When CM08 – 392 = 0: 2s ON – 4s OFF 3 : When CM08 – 392 = 1: 0.4s ON – 0.2s OFF – 0.4s ON – 2s OFF When the data for CM35 YY = 18 is set to 0, as- sign the data for converting the received digit.• Y = 0 (Day Mode) • Y = 1 (Night Mode) (1) X-XXXX: Station No. received (2) D09: Automated Attendant Assign the DTMF Receiver for the Automated Attendant.•Y = 2 (1) XX X: DTMF Receiver No. *a *b *a: Card No. of PN-8RST (Last two digits of E200-E215 assigned by CM10) *b: Circuit No. (0–3) (2) 0: Only for Automated Attendant 1 : Station and Tie Line/DID/ Automated Attendant Specify whether the inter-tenant connection is allowed on an Automated Attendant incoming call.•Y = 2 (1) XX XX *a *b *a: Tenant No. (00-63) of called station *b: Tenant No. (00-63) of trunk (2) 0/1 : Restricted/Allowed CM35 B CM76 CM63 C CM45
CHAPTER 4 ND-45857 (E) Pag e 9 0 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Assign the answering method of the Automated Attendant to the required tenants.•Y = 0 (1) Tenant No. (00 – 63) (2) 00: DT Connection 02: 1st Answering Message followed by DT Connection 03 : DT Connection Assign the data of Hold Tone Sending. • Y = 0 (1) 00:C.O. Line (2) 1400: Hold Tone Source on MP Card If no Dial tone connection is required for the answering system assigned by CM64 Y = 0, set data “0”.•Y = 2 (1) 06 (2) 0/1 : Without DT/With DT Specify the ringing rate for an Automated At- tendant Call.(1) 180 (2) 0/1: 0.2s ON – 0.2s OFF – 0.2s ON – 0.2s OFF – 0.2s ON – 2s OFF /As per CM35 YY = 33 Specify the process when a call is transferred by an Automated Attendant to a predetermined Station and time-out occurs.(1) 359 (2) 0/1 : Disconnect the call/Continue to call Specify the process for an Automated Atten- dant call when a caller dials while receiving the message.(1) 363 (2) 0/1 : Not allowed (Allowed after re- ceiving the message)/AllowedCM64 D C CM48 CM08
ND-45857 (E) CHAPTER 4 Page 91 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Specify the Terminating System for called Par- ty Subaddress.(1) 401 (2) 0: Station Call 1 : Terminating System assigned by CM30 YY = 02, 03 Specify the time before an Automated Atten- dant call is redirected because no digits are re- ceived from the calling party.•Y = 0 (1) 34 (2) 01 – 30: 0 – 120 sec. If no data is set, the default setting is 32 – 36 seconds. Specify the timing of unanswered call after for- warding to predetermined station in Automated Attendant.•Y = 0 (1) 39 (2) 01 – 30: 0 – 120 sec. If no data is set, the default setting is 32 – 36 seconds. Specify the time before Dial Tone timeout in Automated Attendant.•Y = 0 (1) 43 (2) 01 – 14: 1 – 14 sec. If no data is set the default setting is 14 seconds.CM08 D CM41 END
CHAPTER 4 ND-45857 (E) Pag e 9 2 Revision 3.0 SYSTEM DATA PROGRAMMING When the 1st and/or 2nd answering message is required: CM30 YY=30, 31, Data=08/CM64 Y=0, Data=02, do the following programming. DESCRIPTION DATA Assign a Digital Announcement Trunk Circuit No. to the required LEN. Note:The Digital Announcement Trunk Circuit No. must be assigned to the 1st LEN (Lev- el 0) and/or 3rd LEN (Level 2) of each LT slot. (1) LEN (0000 – 0511) (2) EB000 – EB127: Digital Announcement Trunk Circuit No. EB000 – EB031: For PIM0/1 EB032 – EB063: For PIM2/3 EB064 – EB095: For PIM4/5 EB096 – EB127: For PIM6/7 Assign the function of the Digital Announce- ment Trunk.• YY = 00 (1) XXX: Digital Announcement Trunk Cir- cuit No. (000 – 127) assigned by CM10. (2) XX XX *a *b *a: 01: 1st Answering Message 02: 2nd Answering Message *b:Message No. (00-63) Assign the Message No. to the required tenants.• YY = 01 (For 1st Answering Message) • YY = 02 (For 2nd Answering Message) (1) XX: Tenant No. (00 – 63) (2) XX: Message No. (00 – 63) assigned by YY = 00. To record, replay, or delete a message, assign the respective Digital Announcement Trunk ac- cess codes.• Y = 0 – 3 (Numbering Plan Group 0 – 3) (1) X-XXX: (Access Code) (2) A00: Record A01: Replay A02: Delete Specify the message replay timer for Automat- ed Attendant.•Y = 0 (1) 51 (2) 01-15: 4-60 sec. If no data is set, the default setting is 40 sec. CM10 CM20 START CM49 CM41 END
ND-45857 (E) CHAPTER 4 Page 93 Revision 3.0 SYSTEM DATA PROGRAMMING 3.3.11 Direct Inward System Access (DISA) Assignment To provide the DISA without Application Processor (PN-AP01): DESCRIPTION DATA Designate the processor checking the ID code on DISA.(1) 217 (2) 0: MP (PN-CP00) Designate the Terminating System for Called Party Subaddress.(1) 401 (2) 0/1 : Station Call/Terminating System assigned by CM30 YY = 02/03 Assign the ring rate on a DISA call. (1) 180 (2) 0/1 : 0.2s ON – 0.2s OFF – 0.2s ON – 0.2s OFF – 0.2s ON – 2s OFF /As per CM35 YY = 33 Assign the Trunk Route. • YY = 00 (1) Trunk No. (000 – 255) (2) Trunk Route (00 – 63) Assign the Trunk Tenant. • YY = 01 (1) Trunk No. (000 – 255) (2) Trunk tenant (00 – 63) If no data is set, the default setting is 01. Assign the Terminating System in Day/Night Mode for incoming C.O. Calls.• YY = 02 (Day Mode) • YY = 03 (Night Mode) (1) Trunk No. (000 – 255) (2) 18: ISDN Indial START CM08 A CM30
CHAPTER 4 ND-45857 (E) Pag e 9 4 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Assign the handling of busy/not available/unan- swered Automated Attendant, DISA destina- tion in Day/Night Mode.• YY = 30 (Day mode) • YY = 31 (Night mode) (1) Trunk No. (000 – 255) (2) 00: C.O. Line Release 01: Forwarded to TAS 03: Forwarded to ATTCON 04: Forwarded to DIT Station assigned by CM30 Y = 04, 05. 06: DT Connection for redial 08: C.O. Line Release 15 : C.O. Line Release Assign the handling of timed-out Automated Attendant call.• YY = 32 (Handling of time-out Automated Attendant in day mode) • YY = 37 (Handling of time-out Automated Attendant in night mode) (1) Trunk No. (000 – 255) (2) 00: C.O. Line Release 01: Forwarded to TAS Indicator 03: Forwarded to SN610 ATTCON 04: Forwarded to DIT Station 06: DT Connection for Redial 15 : C.O. Line Release Assign the restriction data for the tandem con- nection within a system to each combination of incoming trunk route and outgoing trunk route.(1) XXXX *a *b *a: Incoming trunk route (00-63) *b: Outgoing trunk route (00-63) (2) 0/1 : Allowed/Restricted Assign the number of digits to be received on DID.• YY = 12 (1) Trunk Route No. (00 – 63) (2) 0: 1 digit 1: 2 digits 2: 3 digits 3 : 4 digitsCM30 A CM35 CM36 B
ND-45857 (E) CHAPTER 4 Page 95 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Assign the data for digit conversion on DID call to the Route No. assigned by CM30 YY = 00 when providing DISA to the DID call.• YY = 18 (1) Trunk Route No. (00 – 63) (2) 0/1 : To be provided/Not to be provided When the data for CM35 YY = 18 is set to 0, as- sign the data for converting the received digit(s) to DISA.• Y = 0 (Day Mode) • Y = 1 (Night Mode) (1) X-XXXX:Station No. received (2) D16: DISA Assign the ID code for DISA. The maximum number of digits for an ID code is specified by CM42 – 13.•Y = 5 (1) XX: 00 – 07 (ID code serial number) (2) X – X...X:ID code (Max. 16 digits) Assign required Trunk Restriction Class to each ID code.•Y = 6 (1) XX: 00 – 07 (ID code serial number) (2) 1 : Unrestricted (RCA) 2: Non-Restricted-1 (RCB) 3: Non-Restricted-2 (RCC) 4: Semi-Restricted-1 (RCD) 5: Semi-Restricted-2 (RCE) 6: Restricted-1 (RCF) 7: Restricted-2 (RCG) 8: Fully-Restricted (RCH) Assign the required Service Class A/B to each ID code. The features available in each class are assigned by CM15.•Y = 7 (1) XX: 00 – 07 (ID code serial number) (2) XXXX *a *b *a: Service Feature Class (A) (00–15 ) *b: Service Feature Class (B) (00–15 ) Assign required Service Class C to each ID code. The features available in each class are assigned by CM15.•Y = 8 (1) XX: 00 – 07 (ID code serial number) (2) XX: 00 – 15 (Service Restriction Class (C))CM35 B CM76 C CM2A
CHAPTER 4 ND-45857 (E) Pag e 9 6 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Specify the maximum number of digits for ID Code on DISA.(1) 13 (2) 01 – 16 (Number of digits) If no data is set, 10 digits of ID Code are avail- able.CM42 C END
ND-45857 (E) CHAPTER 4 Page 97 Revision 3.0 SYSTEM DATA PROGRAMMING To provide the DISA with AP (PN-AP01): DESCRIPTION DATA Assign the slot number to the PN-AP01 card. The SENSE Switch on the PN-AP01 card should be set to the slot number assigned by this command. (1) Slot No. (04 – 15) (2) 07 Designate the processor checking the DISA ID Codes.(1) 217 (2) 1 : AP (PN-AP01) Designate the Terminating System for Called Party Subaddress.(1) 401 (2) 0/1 : Station Call/Terminating System assigned by CM30 YY = 02/03 Assign the ring rate on a DISA call. (1) 180 (2) 0/1: 0.2s ON – 0.2s OFF – 0.2s ON – 0.2s OFF – 0.2s ON – 2s OFF /As per CM35 YY = 33 Assign the Trunk Route. • YY = 00 (1) Trunk No. (000 – 255) (2) Trunk Route (00 – 63) START CM05 A CM08 CM30 INITIAL
CHAPTER 4 ND-45857 (E) Pag e 9 8 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Assign the Trunk Tenant. • YY = 01 (1) Trunk No. (000 – 255) (2) Trunk Tenant (00 – 63) If no data is set, the default setting is 01. Assign the Terminating System in Day/Night Mode for incoming C.O. Calls.• YY = 02 (Day Mode) • YY = 03 (Night Mode) (1) Trunk No. (000 – 255) (2) 18:ISDN Indial Assign the handling of busy/not available/unan- swered Automated Attendant, DISA destina- tion in Day/Night Mode.• YY = 30 (Day mode) • YY = 31 (Night mode) (1) Trunk No. (000 – 255) (2) 00: C.O. Line Release 01: Forwarded to TAS 03: Forwarded to ATTCON 04: Forwarded to DIT Station assigned by CM30 YY = 0. 06: DT Connection for redial 08: C.O. Line Release 15 : C.O. Line Release Assign the handling of timed-out Automated Attendant call.• YY = 32 (Handling of time-out Automated Attendant in day mode) • YY = 37 (Handling of time-out Automated Attendant in night mode) (1) Trunk No. (000 – 255) (2) 00: C.O. Line Release 01: Forwarded to TAS Indicator 03: Forward to SN610 ATTCON 04: Forward to DIT Station 06: DT Connection for Redial 15 : C.O. Line Release Assign the restriction data for the tandem con- nection within a system to each combination of incoming trunk route and outgoing trunk route.(1) XXXX *a *b *a: Incoming trunk route (00 – 63) *b: Outgoing trunk route (00 – 63) (2) 0/1 : Allowed/RestrictedCM30 A CM36 B