NEC Neax2000 Ivs Isdn System Manual
Have a look at the manual NEC Neax2000 Ivs Isdn System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ND-45857 (E) CHAPTER 4 Page 109 Revision 3.0 SYSTEM DATA PROGRAMMING 3.5 Basic Data Assignment for ISDN Terminal 3.5.1 ILC Assignment DESCRIPTION DATA Assign an ISDN Circuit Station Number to the required LEN.(1) LEN (0000-0511) (2) EFX-EFXXXX: ISDN Circuit Station No. Assign a Tenant No. to each ISDN Circuit Sta- tion Number.• YY=04 (1) X-XXXX (ISDN Circuit Station No.) (2) 00-63 (Tenant No.) If no data is set, the default data is 01. Assign a Trunk Restriction Class to each ISDN Circuit Station Number.• YY=01 (1) X-XXXX (ISDN Circuit Station No.) (2) X X (Trunk Restriction Class) *a *b *a: Trunk Rest. Class in Day Mode (1 -8) *b: Trunk Rest. Class in Night Mode (1 -8) 1: Unrestricted (RCA) 2: Non-Restricted 1 (RCB) 3: Non-Restricted 2 (RCC) 4: Semi-Restricted 1 (RCD) 5: Semi-Restricted 2 (RCE) Assign an ISDN Indial Number to the required ISDN Circuit Station Number.• YY=12 (1) X-XXXX (ISDN Circuit Station No.) (2) X-XXXX (ISDN Indial No.) Assign a Local Office Code Table Number to the required ISDN Circuit Station Number.• YY=13 (1) X-XXXX (ISDN Circuit Station No.) (2) 00: ISDN Local Office Code Table No. 00 14: ISDN Local Office Code Table No. 14 A CM12 CM10 START INITIAL ~ ~
CHAPTER 4 ND-45857 (E) Pag e 1 10 Revision 3.0 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Specify the facility control of CPN (Calling Party Number).• YY=25 (1) X-XXXX: ISDN Circuit Station No. (2) 0/1 : To be provided/Not to be provided Assign the digit number of ISDN Circuit Sta- tion Number.•Y=0-3 (1) X-XXXX: ISDN Circuit Station No. (2) 801: 1 digit 802: 2 digits 803: 3 digits 804: 4 digits Specify whether the subaddress is sent to an ISDN network when making a call from ISDN Terminal, if required.(1) 430 (2) 0: To be sent (depends on CM08-431) 1 : Not to be sent Specify the calling party subaddress which is sent to an ISDN network when making a call from ISDN Terminal, if required.(1) 431 (2) 0: ISDN Circuit Station No. assigned by CM10 1 : ISDN Terminal No. Specify the forced release when a called ISDN Terminal does not answer during 3 minutes, if required.(1) 432 (2) 0: Not Available 1 : Available Assign the calling party number which is sent to an ISDN network when making a call from ISDN Terminal, if required.(1) 434 (2) 0: Calling Party No. entered in ISDN Ter- minal 1 : Calling Party No. assigned by CM12 YY=12/13 Specify the make busy of B channel (B1, B2) for ISDN Terminal, if required.•Y=2 (1) XXXX X *a *b *a: ISDN Circuit Station No. *b: 0/1 (B1 channel/B2 channel) (2) 0/1 : Make busy set/In service CM13 A CM08 CM20 CME5 END,
ND-45857 (E) CHAPTER 4 Addendum-001 Page 111 AUGUST, 1998 Revision 3.1 SYSTEM DATA PROGRAMMING 3.5.2 ICH Assignment DESCRIPTION DATA Assign slot number to each ICH card (PN- SC02/SC03). The slot number to be assigned must coincide with the value set by the SENS switch on the ICH card.(1) Slot No. (04-15) (2) 13: ICH card Assign the ICH Number to the Slot Number of ICH assigned by CM05.• YY=09 (1) ICH No. (00-11) (2) XX *a *a: Slot No. assigned by CM05 Assign the ISDN Circuit Station Number to the ISDN Circuit Number of ICH card.• YY=00 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) X-XXXX: ISDN Circuit Station No. Specify the method of TEI (Terminal Endpoint Identifier) assignment. Note:This data must be assigned to match the specification of ISDN Terminal. • YY=02 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 0: Manual TEI Assignment 1 : Automatic TEI Assignment Specify the method of Layer 1 activation. Note:This data must be assigned to match the specification of ISDN Terminal. • YY=04 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 0: Always activated 1 : Activated by call event CM05 CM06 CMACSTART END INITIAL INITIAL INITIAL INITIAL INITIAL
CHAPTER 4 ND-45857 (E) Pag e 1 12 Revision 3.0 SYSTEM DATA PROGRAMMING 3.6 Service Data Assignment for ISDN Terminal 3.6.1 Point to Point Connection Assignment MDF ISDN Terminal/TA Max. 1965 ft. (600 m) ILCPBX
ND-45857 (E) CHAPTER 4 Addendum-001 Page 113 AUGUST, 1998 Revision 3.1 SYSTEM DATA PROGRAMMING DESCRIPTION DATA Assign the point to point connection as the Lay- er 2 data link. Note:When Point-to-Point Connection is select- ed, the PBX will address the BRI Terminal with channel select (B1/B2) message. Some BRI Terminals cannot answer the call with this type of signaling. Some of the BRI Terminals re- quire a Calling Party Number sent from the PBX. In this case, use Point-to-Multi- point for CM AC01 and command 1B to assign extensioin number for the BRI Terminal. • YY=01 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 0: Point to Point Connection Assign the TEI Manual Assignment. • YY=02 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 1 : Automatic TEI Assignment Assign the Long Passive Bus. • YY=03 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 1 : Short Distance Passive Bus Assign the always activated as the method of Layer 1 activation.• YY=04 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 1 : Activated by call event. CMACSTART END INITIAL INITIAL INITIAL INITIAL
CHAPTER 4 ND-45857 (E) Pag e 1 14 Revision 3.0 SYSTEM DATA PROGRAMMING 3.6.2 Point to Multipoints Connection Assignment DESCRIPTION DATA Assign the point to multipoints connection as the Layer 2 data link.• YY=01 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 1 : Point to Multipoints Connection Specify the passive bus. • YY=03 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 0: Extended Passive Bus 1 : Short Distance Passive Bus 400407 410417 ILC • Short Distance Passive Bus • Extended Passive Bus MDF ISDN Terminal ISDN Terminal301 300 MDF ILC PBX Max. 1310 ft. (400 m) Max. 164 ft. (50 m)Max. 491 ft. (150 m) CMAC A START INITIAL INITIAL
ND-45857 (E) CHAPTER 4 Page 115 Revision 3.0 SYSTEM DATA PROGRAMMING BRI Programming Example: The following is an example of common BRI Station Programming. DESCRIPTION DATA Assign an ISDN Terminal Multipoints Station Number to the ISDN Circuit Station Number. The numbers assigned in this command are sta- tion numbers that are to be programmed in the BRI terminal. CM 12 YY=12 will use the sta- tion assignments from CM 10.(1) XXXX X *a *b *a: ISDN Circuit Station No. assigned by CM10 *b: ISDN Multipoints Station No. (0-7) (2) X-XXXX:ISDN Terminal Multipoints Sta- tion No. CM 10 0024 = EF 2125 0025 EF2126 CM AC 00 - 000 - 2125 001 - 2126 CM AC 01 - 000 - 1 001 - 1 AC02 - 000 - 1 001 - 1 AC03 - 000 - 1 001 - 1 AC04 - 000 - 1 001 - 1 AC05 - 000 - 1 001 - 1 AC06 - 000 - 1 001 - 1CM 1B - 2125, 0 = 2225 * 2125. 1 = 2226 2 = None 7 2126. 0 = 2235* 2126. 1 = 2236* 2 = None 7 * Ext. 2225 and others assigned in CM1B are the Extension Numbers that should be entered into the BRI Terminal(s). Most BRI Terminals require a 10-digit number. Use NPA NNX 2225. If the BRI Terminal requires a SPID, it is common to add a 3- digit number to the main number. For example: Main Number (1)214-555-2225 Main Number (2)214-555-2226 SPID (1)214-555-2225123 SPID (2)214-555-2226123 SPIDs are required for NI-1 protocol and AT&T Point-to-Multipoint. Devices that are set as AT&T Point-Point do not use SPIDs.CM1B A END , ~ ~
CHAPTER 4 ND-45857 (E) Page 115-1 Addendum-001 Revision 3.1 AUGUST, 1998 SYSTEM DATA PROGRAMMING 3.6.3 National ISDN 1 BRI Terminal Assignment DESCRIPTION DATA Assign the point to multipoints connection as the Layer 2 data link.• YY=01 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) 1 : Point to Multipoints Connection Specify the passive bus. Assign protocol as National ISDN 1.• YY=03 (1) XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) (2) • (1) (2)1 : Short Distance Passive Bus YY=10 XX X *a *b *a: ICH No. (00-11) *b: ISDN Circuit No. of ICH card (0-7) 0: National ISDN 1 (NI-1) Assign an ISDN Terminal Multipoints Station Number to the ISDN Circuit Station Number. The numbers assigned in this command are sta- tion numbers that are to be programmed in the BRI terminal. CM 12 YY=12 will use the sta- tion assignments from CM 10.(1) (2)XXXX X *a *b *a: ISDN Circuit Station No. assigned by CM10 *b: ISDN Multipoints Station No. (0-7) X-XXXX:ISDN Terminal Multipoints Sta- tion No. CMACSTART CM1B END INITIAL INITIAL ,
ND-45857 (E) CHAPTER 4 Addendum-001 Page 115-2 AUGUST, 1998 Revision 3.1 This page is for your notes.
CHAPTER 4 ND -4 5857 ( E) S YST EM DATA P RO G RA MMING ISDN IS DN Term inal I L C P BX C M 30 A CM 35