NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 4 02
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
DESCRIPTION DATA
Assign the Service Restriction Class C to each 
station.• YY = 07
(1) X-XXXX:Primary Extension No.
(2) XX:Service Restriction Class C (00-15)
Provide the switch hook flash capability dur-
ing C.O. line connection, to the required sta-
tions.• YY = 90, 91
(1) 00-15:Service Restriction Class C
(2) 1 :Allowed
Specify the combination of trunk routes al-
lowing the Trunk to Trunk Connection.(1) XX
 XX
Incoming trunk...

ND-45670 (E) CHAPTER 2
Page 403
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
DESCRIPTION DATA
Provide the system with Trunk to Trunk Con-
nection when no release signal arrives from 
the incoming trunk route and answer signal ar-
rives from the outgoing trunk route.(1) 324
(2) 0/1 :Available/Not available
Provide the system with Trunk to Trunk Con-
nection transferred by a station or an atten-
dant, when no answer signal arrives and 
release signal arrives from the outgoing trunk 
route.(1) 028
(2) 0/1...

CHAPTER 2 ND-45670 (E)
Pag e 4 04
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
To provide the AMP trunk for Trunk-to-Trunk Connection (1500 Series Enhancement):
DESCRIPTION DATA
Assign the Card Number of the AMP trunk 
(PN-2AMP).
Maximum of two digits are available.
Note:The AMP card number must be
assigned to both of the first LEN
(Level 0) and the third LEN (Level 2)
of each slot.(1) LEN (0000-0511)
(2) Card No. of AMP trunk
C100-C115 : For PIM0/1
C116-C131 : For PIM2/3
C132-C147 : For PIM4/5
C148-C163 : For...

ND-45670 (E) CHAPTER 2
Page 405
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
DESCRIPTION DATA
Select the Tone Disabler’s mode on each AMP 
pattern.• YY=04
(1) 00-14: AMP pattern No. 00-14
(2) 0:G164
1 : G165
Specify the Detect Timing of Tone Disabler on 
each AMP pattern.• YY=05
(1) 00-14: AMP pattern No. 00-14
(2) 0:0 sec.
1 : 2 sec.
Specify the channels connected to each AMP 
pattern.• YY=06
(1) 00-14: AMP pattern No. 00-14
(2) 0:Incoming route: Tie Line
Outgoing route: C.O. Line
1 :Incoming route: C.O....

CHAPTER 2 ND-45670 (E)
Pag e 4 06
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
PROGRAMMING
To activate UCD:
DESCRIPTION DATA
For each UCD Group, assign station numbers, 
one by one, in the order of hunting. 
Note:Up to 60 stations can be assigned
into a single UCD group.
Example:
 For setting Station Numbers 200, 
201, 202 into one UCD Group. 
1st Operation (1) 200 
(2) 200
2nd Operation(1) 201
(2) 202
3rd Operation (1) 202
(2) 200•Y = 0
(1) X-XXXX (Station No.)
(2) X-XXXX (Another Station...

ND-45670 (E) CHAPTER 2
Page 407
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
DESCRIPTION DATA
• Y = 6 (Tie Line Incoming Call) 
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 : Not to be provided/To be provid-
ed 
• Y = 7 (DID Call) 
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 :Not to be provided/To be 
provided
• Y=B (Designation of the number of 
queuing in each UCD group)
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 : To be provided (See CM42-16)/
Not...

CHAPTER 2 ND-45670 (E)
Pag e 4 08
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
DESCRIPTION DATA
Specify the processing for an incoming call 
when all UCD Stations are busy.(1) 212 
(2) 0/1 :Busy Tone Connection /Queuing
Specify the processing for a held call after set-
ting the UCD Busy-Out.(1) 214 (For the held Call from Tie Line)
(2) 0/1 :Reconnected by Switch Hook 
Flash/Disconnected 
(1) 215 (For the held call from C.O. Line)
(2) 0/1 :Reconnected by Switch Hook 
Flash/Disconnected...

ND-45670 (E) CHAPTER 2
Page 409
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
To provide the delay announcement for UCD:
DESCRIPTION DATA
Assign a Digital Announcement Trunk Cir-
cuit No. to each LEN No.(1) 0000-0511 (LEN No.)
(2) EB000-EB127 (Digital Announcement 
Trunk Circuit No.)
Assign the Class of Service for Digital An-
nouncement Trunk Access (Record/Replay/
Delete) to the required station.• CM12 YY=02
(1) X-XXXX: Station No.
(2) XX
XX
*a 
*a: Service Restriction Class (A)
(00-15 )
•...

CHAPTER 2 ND-45670 (E)
Pag e 4 10
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
DESCRIPTION DATA
Assign an access code to record, replay, and 
delete the Digital Announcement Trunk.• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXXX: Access code
(2) A00: Record
A01: Replay
A02: Delete
When transferring the call to an extension or 
Attendant after the 1st interval time of UCD 
Delay Announcement, assign the destination.
Note:This command is only effective when
CM17, Y=A is set to 0 (to be sent pe-...

ND-45670 (E) CHAPTER 2
Page 411
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
To monitor a UCD call, with or without a Warning Tone:
DESCRIPTION DATA
Specify the warning tone sent to connected 
parties (in two-way calling) when monitoring.(1) 259 
(2) 0: No Tone
1 : One Warning Tone 
Assign the Class of Service for monitoring 
stations. • CM12 YY = 02 
(1) X-XXXX: Station number
(2) XX
XX
*a: Service Restriction Class (A) (00-
15 )
• CM15 YYY = 103 
(1) XX: [Service Restriction Class (A)...