NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 3 72
Revision 2.0
STATION HUNTING: STATION HUNTING-SECRETARIAL
PROGRAMMING
DESCRIPTION DATA
Assign a Secretary Station Serial Number to 
each Station Hunting Group.
Note:A maximum of 31 extensions can be
members of the Secretarial Hunt
group.•Y=2
(1)  X-XXXX: Pilot Station No. (Terminal)/
All Member Station numbers 
(Circular)
(2) 00-30 (Secretary Station Serial No.)
Assign a station number to each Secretary Sta-
tion Serial Number assigned by CM18Y=2.•Y=0
(1) 00-30...

ND-45670 (E) CHAPTER 2
Page 373
Revision 2.0
STATION MESSAGE DETAIL RECORDING (SMDR)
PROGRAMMING 
Refer to the SMDR System Manual.
HARDWARE REQUIRED 
Refer to the SMDR System Manual. 

CHAPTER 2 ND-45670 (E)
Pag e 3 74
Revision 2.0
STATION SPEED DIALING
PROGRAMMING
1. To provide an Extension Memory card (PN-ME00) for extending memory for Station Speed Dialing and
One Touch keys:
DESCRIPTION DATA
Assign a slot number to the Extension Memory 
card. The slot number is given by the SENSE 
switch on the Extension Memory card.(1) 04-15 (Slot Number)
(2) 19 (PN-ME00 card)
Provide the system with the Extension 
Memory card.(1) 56
(2) 1: To be provided
START
CM05
CMD000
END
INITIAL 

ND-45670 (E) CHAPTER 2
Page 375
Revision 2.0
STATION SPEED DIALING
2. To provide Single Line Telephone or Multiline Terminal:
DESCRIPTION DATA
Specify whether 1000-Slot Memory Block has 26 
digits or 16 digits memory buffers.
Note:When CM08-252 is assigned as 0, only
3000 Station Speed Dialing numbers
can be assigned, and 1000-Slot Memory
Block No. 0-2 contains 26-digits memo-
ry buffers. When CM08-252 is assigned
as 1, 4500 Station Speed Dialing num-
bers can be assigned, and 1000-Slot
Memory Block No....

CHAPTER 2 ND-45670 (E)
Pag e 3 76
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Specify “*” dialing is set as programmable 
pause by CM41-38 or dialed digit when the 
DTMF station or Multiline Terminal dials “*” 
in the setting of the Station Speed Dialing fea-
ture.(1) 171
(2) 0/1 :Programmable pause by CM41-
38/Dialed digit
Allocate the memory area for Station Speed 
Dialing to each station. The memory block for 
storing one called number of Station Speed 
Dialing is called a “Memory Parcel”. An...

ND-45670 (E) CHAPTER 2
Page 377
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Note 1:
If the system provides the Extension Memory card, 1000-Slot Memory Block No. 8-F (8000
Memory Parcels) can be used. For using this memory area, there are several conditions as
mentioned below: 
• This memory area cannot be used for Speed Dialing with Speed Dialing keys provided
by CM90-second data: F11XX on a Multiline Terminal, and cannot also be used for
System Speed Dialing.
• When exchanging an Extension...

CHAPTER 2 ND-45670 (E)
Pag e 3 78
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Assign Station Speed Dialing keys on each 
Multiline Terminal, if required.• YY=00
(1) Primary Extension No. +   + Key No. 
(01-24)
(2) F11XX
 
*a 
*a: 00: Station Speed Dialing 00 
99: Station Speed Dialing 99
CM90
C
END
, 

ND-45670 (E) CHAPTER 2
Page 379
Revision 2.0
STATION SPEED DIALING
3. To provide Multiline Terminal with One Touch keys (ETJ-16DD-1/ETJ-24DS-1/DTP-32-1/DTP-32D-1):
DESCRIPTION DATA
Specify whether 1000-Slot Memory Block has 
26 digits or 16 digits memory buffers.
Note 1:When CM08-252 is assigned as 0,
only 3000 Station Speed Dialing
numbers can be assigned, and 1000-
Slot Memory Block No. 0-2 contains
26-digits memory buffers. When
CM08-252 is assigned as 1, 4500
Station Speed Dialing numbers can
be...

CHAPTER 2 ND-45670 (E)
Pag e 3 80
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Allocate the memory area for Station Speed 
Dialing to each station. 
The memory block for storing one called 
number of Station Speed Dialing is called a 
“Memory Parcel”. 
An assembly of 10-Memory Parcels is called 
a “10 Slot Memory Block,” and one hundred 
10-Slot Memory Blocks are called a “1000-
Slot Memory Block”.(1) X-XXXX (Primary Extension No.)
(2) X
 XX 0 XX 
*a *b  *c 
*a: 1000-Slot Memory Block No. 
(0-4,...

ND-45670 (E) CHAPTER 2
Page 381
Revision 2.0
STATION SPEED DIALING
4. To provide the One Touch key to send “Hooking Signal + Called Number” to a Centrex, set the following
data in addition to the programming (2). (1500 Series Enhancement)
 
5. To provide the One Touch key to send “Called Number + DTMF Signal” for such as VMS operation, set
the following data in addition to the programming (2), when the called number includes a trunk access code.
If the called number includes no trunk access code, this...