NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 3 62
Revision 2.0
RINGING LINE PICKUP
PROGRAMMING
HARDWARE REQUIRED 
ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card.
DESCRIPTION DATA
Assign the Class of Service for Ringing-Line 
Pickup.•  CM12 YY = 07 
(1)  X-XXXX (Primary Extension) 
(2)  00-15  (Service Restriction Class C) 
•  CM15 YY = 82 
(1)  00-15 (Service Restriction Class C as-
signed by CM12 YY = 07) 
(2) 0: Allowed
Assign the Class of Service for Ringing-Line 
Pickup by ANS key, if required.•...

ND-45670 (E) CHAPTER 2
Page 363
Revision 2.0
ROUTE ADVANCE
PROGRAMMING
DESCRIPTION DATA
Assign the access code to Route Advance 
Block 00-31.•  Y = 0-3 (Numbering Plan Group 0-3) 
(1)  X-XXX (Route Advance Access Code) 
(2)  200: Route Advance Block 00
 
231: Route Advance Block 31 
Specify the alternative routes with the order of 
priority to be seized. Up to seven alternative 
routes can be set by using two Route Advance 
Blocks, as shown below.•  YY = 00-31 (Route Advance Block as-
signed by CM20,...

CHAPTER 2 ND-45670 (E)
Pag e 3 64
Revision 2.0
SAVE AND REPEAT
PROGRAMMING
 
HARDWARE REQUIRED 
ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card.
DESCRIPTION DATA
Assign the SAVE & REPEAT key to the Mul-
tiline Terminal. 
Note:Up to three Save and Repeat keys can
be assigned per Multiline Terminal. •  YY = 00
(1)  Primary Extension No. +   + Key No. 
(2) F1001, F1013, F1014 
START
END
CM90
, 

ND-45670 (E) CHAPTER 2
Page 365
Revision 2.0
SECURITY ALARM
PROGRAMMING 
DESCRIPTION DATA
Assign the Hot Line to the Station connected 
to the contact.•  YY = 03
(1) X-XXXX (Station No.) 
(2)  04: Hot Line
Assign the SN610 ATTCON as the Hot Line 
destination of the Station. •  YY = 00-99 (Hot Line Pair No.) 
(1) 0: Calling Side 
(2)  X-XXXX (Station No. associated with 
the contact closure.) 
(1)  1: Called Side 
(2) E00X
*a: SN610 ATTCON No.0-7 assigned 
by CM10. 
START
END
CM12
CM52
*a 

CHAPTER 2 ND-45670 (E)
Pag e 3 66
Revision 2.0
SIX/TEN-PARTY CONFERENCE
PROGRAMMING
To use this feature by dialing the feature access code:
DESCRIPTION DATA
Assign the card number of the Conference 
trunk (CFT card) to the required LENs. 
Note:The CFT card number must be as-
signed to the first LEN (Level 0) of
each LT slot. (1) LEN: 0000-0511
(2) ED00-ED03: CFT card No. 
Assign the Service Restriction Class B for 
Conference leader.• CM12 YY = 02 
(Service Restriction Class A·B)
(1) X-XXXX: Primary...

ND-45670 (E) CHAPTER 2
Page 367
Revision 2.0
SIX/TEN-PARTY CONFERENCE
To use this feature by using the feature keys assigned on the Multiline Terminal (1500 Series Enhancement):
DESCRIPTION DATA
Assign the feature key for Six/Ten-Party Con-
ference, on the Multiline Terminal of the Con-
ference leader.• YY=00
(1) Primary Extension No. +  + key No. 
(2) F0A85 :6-party conference
F0A86 : 10-party conference
Assign maximum of 6 or 10 Multiple Line 
keys on the Multiline Terminal of the Confer-
ence leader.•...

CHAPTER 2 ND-45670 (E)
Pag e 3 68
Revision 2.0
SOFTWARE LINE APPEARANCE
PROGRAMMING 
DESCRIPTION DATA
Assign a Software Line Appearance (Virtual-
Line Station Number) to the required Virtual 
LEN.
The Virtual LENs have no relation with the 
physical LENs used in CM10. Therefore, any 
Virtual LENs can be assigned to each Virtual 
Line Station Number. However, the Virtual-
Line Station Number should be different from 
the Single-Line Number assigned by CM10.(1) Virtual LEN (0000-0255) 
(2)  X-XXXX...

ND-45670 (E) CHAPTER 2
Page 369
Revision 2.0
STACK DIAL
PROGRAMMING
 
To provide SN610 ATTCON with this feature (1200 Series Enhancement):
DESCRIPTION DATA
Specify whether Stack Dial is to be activated 
for an internal call. (1) 178
(2)  0: Not to be activated
1 : To be activated
Assign Service Restriction Class (C) to the re-
quired stations.•  YY = 07
(1)  X-XXXX: Station number
(2)  00-15 : Service Restriction Class (C)
Specify the Multiline Terminal LCD display 
service.•  YY = 96
(1)  00-15: Service...

CHAPTER 2 ND-45670 (E)
Pag e 3 70
Revision 2.0
STATION HUNTING: STATION HUNTING-CIRCULAR
PROGRAMMING
 
Note 1:The maximum number of stations per hunt group is 60.
There is no limit to the number of Circular Hunt groups within the system.
Note 2:Each station can belong to only one hunt group.
Note 3:The Attendant Console cannot be a member of a hunt group.
DESCRIPTION DATA
To set up each Hunting Group, assign the sta-
tion numbers, one-by-one, in the order of 
hunting, as shown below:
Note:
For setting...

ND-45670 (E) CHAPTER 2
Page 371
Revision 2.0
STATION HUNTING: STATION HUNTING-TERMINAL
PROGRAMMING
 
Note:The maximum number of stations that can be included in one Station Hunting group is 60, including the
pilot station. There is no limit to the number of Terminal Hunt groups within the system.
DESCRIPTION DATA
To set up each Station Hunting Group, assign 
the station numbers, one by one, as shown be-
low.
1st Operation
(1) Station A
(2) Station B
2nd Operation
(1) Station B
(2) Station C•Y=0
(1)...