NEC Neax2000 Ivs Circuit Card Manual

							ND-45504 (E) CHAPTER 4
Page 63
Revision 2.0
PN-BRTA (BRI)
(2) Lamp Indications
Lamp Indications on the PN-BRTA (BRI) Card
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
B1 GreenB1 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):Make Busy
B2 GreenB2 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):Make Busy
DGreenD channel status
ON: Busy
OFF: Idle
ALM RedTransmission line fault status
ON: Line fault
OFF: Normal operation 
						

							CHAPTER 4 ND-45504 (E)
Pag e 64
Revision 2.0
PN-BRTA (BRI)
(3) Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION col-
umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and
 , the setting of the switch varies with the system concerned.
Note 1:Set the groove on the switch knob to the desired switch position.
Note 2:When the power is on, set the MB switch to ON (UP position) before plugging/unplugging the circuit
card.
Switch Settings on the PN-BRTA (BRI) Card 
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SENS
(Rotary SW)
Note 14 - F Set the switch to match the AP Number (04 - 15) as set by CM05.
0 - 3 Not used
MB (Toggle SW)
Note 2UPFor make-busy
For normal operation
SW0 (Dip SW)
1For normal operation (BRI mode)
OFF Not used
2
Note 3ONClock signal from a master office is sent to the PLO of 
MP card according to the switch setting of SW0-3.
OFFClock signal from a master office is not sent to the PLO 
of MP card.
3
Note 3ON Clock signal is sent to PLO 0 of MP card.
OFF Clock signal is sent to PLO 1 of MP card.
4For normal operation
OFF Not used
SW1 (Dip SW)
1For terminating the transmitting side of channels B1 and 
B2 with 100 ohms.
OFFTo remove the terminating resistor on the transmitting 
side of channels B1 and B2.
2For terminating the receiving side of channels B1 and B2 
with 100 ohms.
OFFTo remove the terminating resistor on the receiving side 
of channels B1 and B2.
0AP NO.
SW NO.10 04 05 06 07 08 09 11 12 13 14 15
456 789ABCDEF
ON
DOWN
ON43 2 1
ON
ON
ON2 1
ON
ON 
						

							ND-45504 (E) CHAPTER 4
Page 65
Revision 2.0
PN-BRTA (BRI)
Note 3:
Set SW0-2 and SW0-3 as follows.
BRI 0 BRI 1 BRI 2 .... BRI 11
REMARKS
SW 
0-2SW 
0-3SW 
0-2SW 
0-3SW 
0-2SW 
0-3....SW 
0-2SW 
0-3
When one BRI is 
provided.ON ONThe MP card will receive the clock signal 
from BRI 0 at its PLO 0 input.
When more than 
one BRI is pro-
vided.
ON ON ON OFF OFF ON .... OFF ONThe MP card will receive the clock signal 
from BRI 0 at its PLO 0 input under nor-
mal conditions.
Should a clock failure occur on BRI 0, the 
MP card will automatically switch to the 
PLO 1 input, and so derive the clock from 
BRI 1.No. of BRI
SW
CONDITIONS 
						

							PN-2BRTC (BRI)
CHAPTER 4 ND-45504 (E)
Page 65-1 Addendum-001
Revision 2.1 JULY, 1998
PN-2BRTC (BRI)
1. Locations of Lamps, Switches, and connectors
PN-2BRTC (BRI) Card
RU N
SENS
MB
SW0
D1
ALM1
B20
B10
SW11SW10
D0
ALM0
B21
B11 
						

							PN-2BRTC (BRI)
ND-45504 (E) CHAPTER 4
Addendum-001 Page 65-2
JULY, 1998 Revision 2.1
2. Lamp Indications
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
B21 Red No.1 Circuit B2 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
B11 Red B1 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
D1 Green D channel status
ON: Busy
OFF: Idle
ALM1 Red Transmission line fault status
ON: Line fault
OFF: Normal operation
B20 Red No.0 Circuit B2 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
B10 Red B1 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
D0 Green D channel status
ON: Busy
OFF: Idle
ALM0 Red Transmission line fault status
ON: Line fault
OFF: Normal operation 
						

							PN-2BRTC (BRI)
CHAPTER 4 ND-45504 (E)
Page 65-3 Addendum-001
Revision 2.1 JULY, 1998
3. Switch Settings
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENS
(Rotary SW)
Note 14 ~ F Set the switch to match the AP Number (04-15) as set by
CM05.
0 
~ 3 Not used
MB (Toggle SW)
Note 2UP For make-busy
For normal operation
SW0, SW10
(Dip SW)
1For terminating the transmitting side
of channels B1 and B2 with 100 ohms.
OFFTo remove the terminating resistor on
the transmitting side of channels B1
and B2.
2For terminating the receiving side of
channels B1 and B2 with 100 ohms.
OFFTo remove the terminating resistor on
the receiving side of channels B1 and
B2.
0
AP No.
04 05 06 07 08 09 10 11 12 13 14 15
SW No.
456789ABCDEF
ON
DOWN
1ON2
ON
ON 
						

							PN-2BRTC (BRI)
ND-45504 (E) CHAPTER 4
Addendum-001 Page 65-4
JULY, 1998 Revision 2.1
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the figure and
, the setting of the switch varies with the system concerned.
Note 1:Set the groove on the switch knob to the desired switch position.
Note 2:When the power is on, set the MB switch to ON (UP position) before plugging/unplugging the circuit
card.
Note 3:
The system can supply clock signals from two clock supply routes.
In normal condition, the system synchronizes to the clock signals supplied on the PLO 0 of MP card via
the Back Wiring Board, and if the clock signals are failed, the clock supply route takes over to PLO1
automatically. Set SW11-2 and SW11-3 as follows. SW11 (Dip SW)
1For normal operation (BRI mode)
OFF Not used
2
Note 3ONOutput clock signals according to the
switch setting of SW11-3.
OFF Do not output clock signals.
3
Note 3ON Output clock signals to PLO 0 of MP.
OFF Output clock signals to PLO 1 of MP.
4For normal operation
OFF Not used
BRI  0 BRI  1 BRI  2 ---- BRI  11
REMARKS
SW
11-2SW
11-3SW
11-2SW
11-3SW
11-2SW
11-3----SW
11-2SW
11-3
When one BRI is 
provided.ON ONThe clock signals are supplied to the
PLO through No. 0 circuit the BRI. If
the clock supply route of No. 0 circuit
is failed, the clock supply route of No.
1 circuit takes over automatically.
When more than 
one BRI is pro-
vided.ON ON ON OFF OFF ON
----OFF ONThe system can supply the clock
signals from BRI 0 or BRI 1. The
system is synchronized to the BRI 0
clock signals normally, and if both
No. 0 circuit clock supply route and
No. 1 circuit clock supply route is
failed, the BRI 1 takes over. Switch Settings (Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1234 ON
ON
ON
No. of
BRI
SW
CONDITIONS 
						

							CHAPTER 4 ND-45504 (E)
Pag e 66
Revision 2.0
PN-CC00 (ETHER)
PN-CC00 (ETHER)
1. Locations of Lamps, Switches, and Connectors
PN-CC00 (ETHER) Card
ETHER
RUN
IP
SW31
SW
ERR
S1
S2
S3RUN
SW
ERR
S1
S2
S3 PN-CC00 PZ-M397
SW51 
						

							ND-45504 (E) CHAPTER 4
Addendum-001 Page 67
JULY, 1998 Revision 2.1
PN-CC00 (ETHER)
2. Lamp Indications
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Steadily lights while this card is operating normally.
ERR Red Flashes at 120 IPM when system error occurs.
S1 Green Lights when it is transmitting or receiving the data.
S2 Green Lights when it can transmit or receive the data.
S3 Green Lights when the power sets ON. 
						

							CHAPTER 4 ND-45504 (E)
Pag e 68
Revision 2.0
PN-CC00 (ETHER)
(3) Switch Settings
Note:Each equipment must have a unique MAC address to distinguish between systems. Therefore, when more
than one PBX is installed in the same network, assign the lower 3 digits of the following MAC address by
SW31 and SW51 to prevent duplicate addresses. 
Switch Settings 
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SW
(Rotary SW)0Always set to 0
1-FNot used
SW51 (Dip SW)
Note1 (D15) ON
2 (D14) ON
3 (D13) ON
4 (D12) OFF
5 (D11) ON
OFF
6 (D10) ON
OFF
7 (D9) ON
OFF
8 (D8) ON
OFF
SW31 (Dip SW)
Note1 (D7) ON
OFF
2 (D6) ON
OFF
3 (D5) ON
OFF
4 (D4) ON
OFF
5 (D3) ON
OFF
6 (D2) ON
OFF
7 (D1) ON
OFF
8 (D0) ON
OFF
000032251   XXX (HEX)
According to the switch setting of SW51 (D11-D8) and SW31 (D7-D0).
Fixed
12345678 ONMAC ADDRESS SWITCH SETTING
00003225   1  X X X 
(HEX)
    FixedSW51-1 (D15)
SW51-2 (D14)
SW51-3 (D13)
SW51-4 (D12)ON
ON
ON
OFF
SW51-5 (D11)
SW51-6 (D10)
SW51-7 (D9)
SW51-8 (D8)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW31-1 (D7)
SW31-2 (D6)
SW31-3 (D5)
SW31-4 (D4)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW31-5 (D3)
SW31-6 (D2)
SW31-7 (D1)
SW31-8 (D0)ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON:0  OFF:1
12345678 ON