NEC Neax2000 Ivs Circuit Card Manual

							ND-45504 (E) CHAPTER 4
Addendum-002 Page 33
OCTOBER, 1998 Revision 2.2
PN-CP00-B/PN-CP00-C (MP)
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION column
indicate the standard setting of the switch. When the switch is not set as shown by the figure and  , the
setting of the switch varies with the system concerned.
Note:Set the groove on the switch to the desired switch position.
Switch Settings (Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW2 (Piano Key SW)
2, 3• When using the PLO card (PN-CK00):
SW2-2
 SW2-3
OFF ON
• When not using the internal PLO and the PLO card:
SW2-2
 SW2-3
OFF OFF
4 ~ 8 Not used
JP0 (Jumper pin)
For normal operation
Memory backup connected
DOWNFor factory testing
(Disconnect battery for memory backup.)
CAUTION
When the operating power is being supplied to this circuit card, do not plug/unplug this circuit card into/from its
mounting slot.
ON
 










OFF
8
7
6
5
4
3
2
1
OFF
Front
UP 
						

							CHAPTER 4 ND-45504 (E)
Page 34 Addendum-002
Revision 2.2 OCTOBER, 1998
PN-CP03/PN-CP03-C (MP)
PN-CP03/PN-CP03-C (MP)
1. Locations of Lamps, Switches, and Connectors
PN-CP03/PN-CP03-C (MP) Card
2. Lamp Indications
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while the circuit card is operating normally.
CLKIN Green Lights while receiving clock signals to the PLO oscillator.
SW3
RUN
SW1
SW2
CLK JAC K
RS1
RS0
VR
JP0
JP1 
						

							ND-45504 (E) CHAPTER 4
Addendum-002 Page 35
OCTOBER, 1998 Revision 2.2
PN-CP03/PN-CP03-C (MP)
(3) Switch Settings
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW3 (Rotary SW)
Note0 ~ FOn Line (Call processing is in progress)
2Off Line (Call processing is stopped)
• I/O port: Depending on CM40 YY=08
3Off Line (Call processing is stopped)
• I/O port: 1200 bps (Fixed)
B For clearing the office data
C For setting the resident system program
1, 4 ~ 9
A, D ~ FNot used
SW1 (Push SW) For initializing the CPU
SW2 (Piano Key SW)
1ON KF Mode
OFF MF/PF Mode
2, 3Selection of PLO (Phase Locked Oscillator)
When using the internal PLO of MP card:
0
ON
 






OFF
4
3
2
1SWITCH NUMBER
FUNCTION
23
OFF OFF1.5 MHz clock 
[For PN-24DTA/PN-24DTA-A]
ON OFF192 kHz clock
[For PN-BRTA]
OFF ON2 MHz clock
[For PN-30DTC/PN-30DTC-A
/PN-2BRTC]
ON ON Not used  
						

							CHAPTER 4 ND-45504 (E)
Page 36 Addendum-002
Revision 2.2 OCTOBER, 1998
PN-CP03/PN-CP03-C (MP)
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION col-
umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and
, the setting of the switch varies with the system concerned.
Note:Set the groove on the switch knob to the desired switch position.
Switch Settings (Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW2 (Piano Key SW)
2, 3• When using the PLO card (PN-CK00):
SW2-2
SW2-3
OFF ON
• When not using the internal PLO and the PLO card:
SW2-2
SW2-3
OFF OFF
4ON When using RS1 port for built-in MODEM
OFF When using RS1 port for RS-232C.
VR (Rotary SW)
Variable Resister for External Hold Tone 
Source
(0 - 20 K
W: Clockwise)
JP0 (Jumper pin)
For normal operation
Memory backup connected
DOWNFor factory testing
(Disconnect battery for memory backup.)
JP1 (Jumper pin)
For normal operation
DOWN For using External Tone Source
CAUTION
When the operating power is being supplied to this circuit card, do not plug/unplug this circuit card into/from its
mounting slot. When the CP03/CP03-C is plugged in and power is on, do not move Jumper JP1.
ON
OFF
4
3
2
1
 








20
0
Front
UP
Front
UP 
						

							ND-45504 (E) CHAPTER 4
Page 37
Revision 2.0
PN-CP01 (FP)
PN-CP01 (FP)
1. Locations of Lamps, Switches, and Connectors
PN-CP01 (FP) Card
2. Lamp Indications
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while the circuit card is operating normally.
MB
RUN SW1 
						

							CHAPTER 4 ND-45504 (E)
Pag e 38
Revision 2.0
PN-CP01 (FP)
(3) Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION col-
umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and
, the setting of the switch varies with the system concerned.
Note 1:Set the groove on the switch knob to the desired switch position.
Note 2:When the power is on, flip the MB switch to ON (UP position) before plugging/unplugging the circuit
card. 
Note 3:The PN-CP01 is required only if any of the following is true:
• More than one PIM is used.
• A PN-2DLCC is used.
• A PN-AP01 is used.
• OAI, ACD, No. 7 CCIS, or ISDN is used.
Switch Settings
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SW1 (Rotary SW)
Note 10 – 3Set this rotary switch to match the location in which this cir-
cuit card is to be mounted.
0 For mounting this card in PIM0
1 For mounting this card in PIM2
2 For mounting this card in PIM4
3 For mounting this card in PIM6
4 – F Not used
MB (Toggle SW)
Note 2UP For make-busy
For normal operation
ON
DOWN 
						

							ND-45504 (E) CHAPTER 4
Addendum-002 Page 39
OCTOBER, 1998 Revision 2.2
PN-CP02/PN-CP02-C (MP)
PN-CP02/PN-CP02-C (MP)
1. Locations of Lamps, Switches, and Connectors
PN-CP02/PN-CP02-C (MP) Card
2. Lamp Indications
Lamp Indications 
LAMP NAME COLOR FUNCTION
RUN Gree n• Flashes at 120 IPM while the circuit card is active status and operating normally.
• Flashes at 30 IPM or 15 IPM while the circuit card is stand by status.
Normally operating: 30 IPM (1 sec - ON, 1 sec - OFF)
Copying office data: 15 IPM (3 sec - ON, 1 sec - OFF)
CLKIN Green Lights while receiving clock signals to the PLO oscillator.
STBY Red Lights when the circuit card is in the standby mode.
SW3
RUN
SW1
SW2
CLKIN
STBY
MT
RS
SW4 JP0 [CP02] Note
JP0 [CP02-C] Note
Note:Location of JP0 is different between CP02 and CP02-C. 
						

							CHAPTER 4 ND-45504 (E)
Page 40 Addendum-002
Revision 2.2 OCTOBER, 1998
PN-CP02/PN-CP02-C (MP)
(3) Switch Settings
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW3 (Rotary SW)
Note 10 ~ F
Note 2On Line (Call processing is in progress)
2Off Line (Call processing is stopped)
• I/O port: Depending on CM40 YY=08
3Off Line (Call processing is stopped)
• I/O port: 1200 bps (Fixed)
B For clearing the office data
C For setting the resident system program
1, 4 ~ 9
A, D ~ FNot used
SW1 (Push SW) For initializing the CPU
SW2 (Piano Key SW)
1ON KF Mode
OFF MF/PF Mode
2, 3Selection of PLO (Phase Locked Oscillator)
• When using the internal PLO of MP card:
0
0
ON
 











OFF
7
8
5
4
3
2
1
6SWITCH
NUMBER
FUNCTION
23
OFF OFF1.5 MHz clock
[For PN-24DTA/PN-24DTA-A]
ON OFF192 kHz clock
[For PN-BRTA]
OFF ON2 MHz clock
[For PN-30DTC/PN-30DTC-A/PN-
2BRTC]
ON ON Not used 
						

							ND-45504 (E) CHAPTER 4
Addendum-002 Page 41
OCTOBER, 1998 Revision 2.2
PN-CP02/PN-CP02-C (MP)
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION col-
umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and
, the setting of the switch varies with the system concerned.
Note 1:Set the groove on the switch to the desired switch position.
Note 2:On the stand by status circuit card, the SW3 can be set to only “0” or “B”. Do not set to the other
position (1-9, A, C-F).
Note 3:MP0 and MP1 must not set to “ON” at the same time.
Note 4:When the power is on, flip the MB switch to ON (UP position) before plugging/unplugging the circuit
card.
Switch Settings (Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW2 (Piano Key SW)
2, 3• When using the PLO card (PN-CK00):
• When not using the internal PLO and the PLO card:
4 ~ 7 Not used
8
Note 3ON Allowed to use MAT
For normal operation
(Not allowed to use MAT)
JP0 (Jumper pin)
For normal operation
Memory backup connected
DOWNFor factory test only
(Disconnect battery for memory backup.)
SW4 (Toggle SW)
Note 4UP For make-busy
For normal operation
ON
 











OFF
7
8
5
4
3
2
1
6
SW2-2
OFFSW2-3ON
SW2-2
OFFSW2-3OFF
OFF
OFF
Front
UP
ON
DOWN 
						

							CHAPTER 4 ND-45504 (E)
Pag e 42
Revision 2.0
PN-PW00 (EXTPWR)
PN-PW00 (EXTPWR)
1. Locations of Lamps, Switches and Connectors
PN-PW00 (EXTPWR) Card
2. Lamp Indications
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Remains lit while –48 V power is being supplied
RUN
MB
CONN