NEC Neax2000 Ivs Circuit Card Manual
Have a look at the manual NEC Neax2000 Ivs Circuit Card Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ND-45504 (E) CHAPTER 4 Page 89 Revision 2.0 PN-SC00 (CCH) (3) Switch Settings Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENS (Rotary SW) Note 14 - F Set the switch to match the AP Number (04 - 15) to be set by CM05. 0 - 3 Not used MB(Toggle SW) Note 2UP For make-busy For normal operation SW0 (Piano Key SW)1ON Loop-back test For normal operation 2ON Analog interface OFF Digital interface 3ONRS-232C RTS signal (to MODEM) ON Note 3 OFF RS-232C RTS signal (to MODEM) OFF 4Always set to ON AP NO. SW NO.10 04 05 06 07 08 09 11 12 13 14 15 456 789ABCDEF ON DOWN ON OFF 4 3 2 1 OFF ON
CHAPTER 4 ND-45504 (E) Pag e 90 Revision 2.0 PN-SC00 (CCH) The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. Note 1:Set the groove on the switch knob to the desired switch position. Note 2:When the power is on, flip the MB switch to ON (UP position) before plugging/unplugging the circuit card. Note 3:This setting is available when SW0-2 is set to ON (Analog Interface). Note 4:The followimg two kinds of rate adaptation method are available when using 48 Kbps data transmis- sion. The rate adaptation method must be set to match the rate adaptation of the master office. SW1(Dip SW)1ON• Common channel signalling data transmission speed (For Digital Interface) • Common channel signalling data transmission speed (For Analog Interface) Set switches (SW1-1 - SW1-5) to OFF. OFF 2ON OFF 3ON OFF 4ON OFF 5ON OFF 6ONA-Law OFFm-law 7Always set to OFF 8 Always set to OFFSwitch Settings (Continued) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK ON2 134 6857 TRANSMISSION SPEEDSW 1-1SW 1-2SW 1-3SW 1-4SW 1-5 48Kbps ¨ ON ON OFF OFF ON 48Kbps ¦ ONONONOFFON 56Kbps ON ON OFF ON ON 64Kbps ONONONONON OFF OFF 11 48 Kbps Data 1 SW1-3: OFF 11 48 Kbps 2SW1-3: ON Data
ND-45504 (E) CHAPTER 4 Page 91 Revision 2.0 PN-SC01 (DCH) PN-SC01 (DCH) 1. Locations of Lamps, Switches and Connectors PN-SC01 (DCH) Card 2. Lamp Indications Lamp Indications LAMP NAME COLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. LC Green Lights when communications are normally ongoing with the D channel data links connected. LPB Green Not used. SENS RUN MB SW0 LC LPB SW1
CHAPTER 4 ND-45504 (E) Pag e 92 Revision 2.0 PN-SC01 (DCH) (3) Switch Settings Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENS (Rotary SW) Note 14 - F Set the switch to match the AP Number (04 - 15) to be set by CM05. 0 - 3 Not used MB(Toggle SW) Note 2UP For make-busy For normal operation SW0 (Piano Key SW) 1OFF AT&T Interface ON Northern Telecom Interface 2OFF No deletion ON Delete the first three digits of all 011 International Calls. 3 Always set to OFF 4 Always set to ON SW1 (Dip SW) 1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4 Always set to OFF 5 Always set to OFF 6 Always set to OFF 7 Always set to OFF 8 Always set to OFF AP NO. SW NO.10 04 05 06 07 08 09 11 12 13 14 15 456 789ABCDEF ON DOWN ON OFF 4 3 2 1 OFF ON ON2 134 6857 OFF OFF OFF OFF OFF OFF OFF OFF
ND-45504 (E) CHAPTER 4 Page 93 Revision 2.0 PN-SC01 (DCH) The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. Note 1:Set the groove on the switch knob onto the intended switch position. Note 2:When the power is on, flip the MB switch to ON (UP position) before plugging/unplugging the circuit card.
CHAPTER 4 ND-45504 (E) Pag e 94 Revision 2.0 PN-SC02 (ICH) PN-SC02 (ICH) 1. Locations of Lamps, Switches, and Connectors PN-SC02 (ICH) Card 2. Lamp Indications Lamp Indications LAMP NAME COLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. DOPE0 GreenON: No. 0 circuit D channel link is connected. OFF: No. 0 circuit D channel link is not connected. DOPE1 GreenON: No. 1 circuit D channel link is connected. OFF: No. 1 circuit D channel link is not connected. RUN MB SW0 SENS DOPE1 DOPE0
ND-45504 (E) CHAPTER 4 Page 95 Revision 2.0 PN-SC02 (ICH) (3) Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. Note 1:Set the groove on the switch knob to the desired switch position. Note 2:When the power is on, flip the MB switch to ON (UP position) before plugging/unplugging the circuit card. Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENS (Rotary SW) Note 14 - F Set the switch to match the AP Number (04 - 15) to be set by CM05. 0 - 3 Not used MB (Toggle SW) Note 2UP For make-busy For normal operation SW0 (Piano Key SW)1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4Always set to ON AP NO. SW NO.10 04 05 06 07 08 09 11 12 13 14 15 456 789ABCDEF ON DOWN ON OFF 4 3 2 1 OFF OFF OFF ON
CHAPTER 4 ND-45504 (E) Pag e 96 Revision 2.0 PN-SC03 (ICH) PN-SC03 (ICH) 1. Locations of Lamps, Switches, and Connectors PN-SC03 (ICH) Card 2. Lamp Indications Lamp Indications on ICH Card LAMP NAME COLOR FUNCTION RUN Green Flashes at 120 IPM while the card is operating normally. DOPE7 Green Lights when No.7 circuit D channel link is connected. DOPE6 Green Lights when No.6 circuit D channel link is connected. DOPE5 Green Lights when No.5 circuit D channel link is connected. DOPE4 Green Lights when No.4 circuit D channel link is connected. DOPE3 Green Lights when No.3 circuit D channel link is connected. DOPE2 Green Lights when No.2 circuit D channel link is connected. DOPE1 Green Lights when No.1 circuit D channel link is connected. DOPE0 Green Lights when No.0 circuit D channel link is connected. SENSE RUN MB DOPE7 DOPE6 DOPE5 DOPE4 DOPE3 DOPE2 DOPE1 DOPE0
ND-45504 (E) CHAPTER 4 Page 97 Revision 2.0 PN-SC03 (ICH) (3) Switch Settings The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. Note 1:Set the groove on the switch knob to the intended switch position. Note 2:When the power is on, flip the MB switch to ON (UP position) before plugging/unplugging the circuit card. Switch Settings on ICH Card SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENSE (Rotary SW) Note 14 ~ F Set the switch to match the AP Number (04 ~ 15) to be set by CM05. 0 ~ 3 Not used MB (Toggle SW) Note 2UPFor make-busy For normal operation AP No. SW No.10 04 05 06 07 08 09 11 12 13 14 15 4 5 6 78 9ABCDEF ON DOWN
CHAPTER 4 ND-45504 (E) Pag e 98 Revision 2.0 PN-SC03 (CSH) PN-SC03 (CSH) 1. Locations of Lamps, Switches, and Connectors PN-SC03 (CSH) Card SENSE RUN MB DOPE7 DOPE6 DOPE5 DOPE4 DOPE3 DOPE2 DOPE1 DOPE0