NEC Neax 2400 Ipx Hotel Feature Programming Manual

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 157
Hotel Feature Transparency Over CCIS H-22
H-22Hotel Feature Transparency Over CCIS
General Description
This feature allows a Hotel System to use Common Channel Interoffice Signaling (CCIS), which conforms to the
CCITT Signaling System No. 7. Some of the hospitality services may be activated over different offices via the
CCIS lines.
Operating Procedure
To originate a CCIS call
1. Dial the office code and the station number from the...

NEAX2400 IPX Hotel Feature Programming ManualPage 158NDA-24304, Issue 1
H-22 Hotel Feature Transparency Over CCIS
Operating Procedure (cont’d)
Figure 12 Call Termination on Attendant Console, Desk Console, and Special Administration Dterm
To set and cancel service features from the Console
1. Press a Feature Key on the Hotel Console.
2. Enter an access code for a distant office, then enter a station number.
3. Enter other information, such as time, if required. When the process ends normally, the Guest...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 159
Hotel Feature Transparency Over CCIS H-22
Service Conditions (cont’d)
5. When a Guest station is enabled to set its own wake-up calls and a log of these settings is desired, then a
hotel printer must be located at the site of the Guest station PBX.
6. The central office lines are accommodated in each office. When placing the central office call, the line
accommodated in the same office is used.
7. When a call terminates from the...

NEAX2400 IPX Hotel Feature Programming ManualPage 160NDA-24304, Issue 1
H-22 Hotel Feature Transparency Over CCIS
✰A-73 Automatic Multiple Attendant Recall —
✰
A-74Answering Camp-On/Call Hold Calls by Switch Hook
Flash—
✰A-75 Automated Guest Station Voice Mail Retrieval —
B-26 Busy Status Display - Hotel Attendant X
C-19 Calendar Display —
C-23 Check-In/Check-Out X*Available from Console / D
term
with Hospitality Functions
C-32 Calling Station Number Display X
✰C-62 Consecutive Speed Calling - System X...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 161
Hotel Feature Transparency Over CCIS H-22
LEGEND:
X: Available —: Not Available
*: Available with some limitations✰: USA and Canada only G-9 Guest Information Display - PMS Terminal —
G-11 Guest Room Calling - Hotel Attendant —
H-8 House Phone/Hot Line —
✰I-23 Inter-Position Transfer 2 —
L-27 Language Service —
M-6 Message Waiting X
M-22 Maid Status X* Available from Console only
M-51 Manual Switching of C.O. Incoming Call...

NEAX2400 IPX Hotel Feature Programming ManualPage 162NDA-24304, Issue 1
H-22 Hotel Feature Transparency Over CCIS
Assignment Procedure
The following data assignment is required in addition to basic data assignment for CCIS.
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX
160b
0Hotel Feature required (Fixed Data)
b
1Hotel Service kind (Fixed Data)
b
2Length of Room Status Memory
0/1 = 8 byte/24 byte
b
3Pattern of Key Arrangement on Console
(Refer toFigure 4) (Usually, 00)
b
4
b5Guest Name Service 0/1 = Out/In...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 163
Inter-Position Transfer 2 I-23
I-23Inter-Position Transfer 2
General Description
This feature is applicable for a multi-attendant environment and will provide for the transfer of an incoming station
or trunk call to a group of attendants by use of the Priority Call key.
An attendant can answer an incoming call, put the call on hold at the Attendant loop, and page the requested party.
The paged party calls the attendant, and if a...

NEAX2400 IPX Hotel Feature Programming ManualPage 164NDA-24304, Issue 1
L-27 Language Service
L-27Language Service
General Description
This service provides the announcement in the Guests language and the language information display in case
following services are activated.
1. Announcement Services - The announcements sent to the Guest will be in his/her language.
AUTOMATIC WAKE-UP [A-10]
AUTOMATIC WAKE-UP - HOTEL ATTENDANT [A-58]
GROUP SERVICE THROUGH PMS [G-4]
2. Language Information Display - When...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 165
Language Service L-27
Assignment Procedure
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX
161b
0Don’t Disturb Override key on Console
0/1 = Out/In Service
b
1Message Waiting Lamp in Service
0/1 = Out/In Service
b
2Language Service
0/1 = Out/In Service
b
3Screening Service
0/1 = Out/In Service
b
4Not used
b
5DSS (Direct Station Section) Keys
0/1 = Out/In service
b
6Timing Start using “#” Code
0/1 = Ineffective/Effective
b
7Timing Start...

NEAX2400 IPX Hotel Feature Programming ManualPage 166NDA-24304, Issue 1
L-27 Language Service
2AHSY
INDEX
1
32For displaying the kind of language information, assign the data by 2 or 4 characters
of ASCII code (INDEXes 1 through 32).
When data are not assigned, the kind of language information is displayed as follows:
Language = 0 : No display
Language = 1 : JPN
Language = 2 : ENG
Language = 3 : GER
Language = 4 : FR
Language = 5 : SP
Language = 6 : CHIN
Language = 7 : RUSS
For example: To change the...