NEC Neax 2400 Ipx Hotel Feature Programming Manual

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 207
Room Cutoff R-9
Service Conditions (cont’d)
4. Through system data programming, a station in ROOM CUTOFF mode can be allowed to access certain
trunk routes, or be restricted from calling certain stations.
5. ROOM CUTOFF mode is set automatically when CHECK-IN/CHECKOUT [C-23] is initiated from the
Console, PMS terminal, or Front Desk Terminal.
6. At this time, if a D
termis used for a Guest station, “RC” may be displayed depending on...

NEAX2400 IPX Hotel Feature Programming ManualPage 208NDA-24304, Issue 1
R-9 Room Cutoff
Note:If unconditional restriction is set as per the OG restriction and IC restriction information, or if OG
restriction and IC restriction are set to Guest stations, the present Route Restriction Class is temporarily
replaced with RSC 13-15, and whether restriction is executed or not is selected from the Restriction Table.
STEP CMND EXPLANATION
3ARSCWhen “1” is assigned in SYS1, ASYD, INDEX 170, Bit 3, assign...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 209
Room Status R-10
R-10Room Status
General Description
This feature provides a ROOM STATUS display on the Console or Front Desk Terminal. The ROOM STATUS
display indicates the following:
AUTOMATIC WAKE-UP [A-10]
DO NOT DISTURB [D-11]
GUEST NAME DISPLAY through PMS [G-5]
MESSAGE WAITING [M-6]
ROOM CUTOFF [R-9]
Room Occupied
Room Reserved
Station number
VIP (PMS option)
Operating Procedure
To display ROOM STATUS on the Console or Front...

NEAX2400 IPX Hotel Feature Programming ManualPage 210NDA-24304, Issue 1
R-10 Room Status
Assignment Procedure
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX
11b
0I/O Port designation to Hotel Printer (Model 60/90/120 PMS)
b
1
b2
b3
Not Used b4
b5
b6Transmission Protocol between PBX and Hotel Printer
b
7
2SYS1
ASYD
INDEX
168b
0Group Announcement Service (for Hotel system)
0/1 = Out/In Service
b
1Audit Reports
0/1 = Out/In Service
b
2Not used
b
3
b4Off-Hook Alarm (service)
0/1 = Out/In Service
b
5Destination...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 211
Room Status R-10
4AHSY
INDEX
179b
0
Not used b1
b2
b3
b4Designation of Guest Station Access Code
b
7b6b5b4ACC · CODE b7b6b5b4ACC · CODE
0000 OutofService 0 1 11 7
0001 1 1 0 00 8
0010 2 1 0 01 9
0011 3 1 0 10 0
0100 4 1 0 11 *
0101 5 1 1 00 #
0110 6 b5
b6
b7
STEP CMND BIT EXPLANATION 

NEAX2400 IPX Hotel Feature Programming ManualPage 212NDA-24304, Issue 1
R-17 Room Numbering
R-17Room Numbering
General Description
This feature enables flexible assignment of station numbers based on the Guest ROOM NUMBERING plan.
Operating Procedure
Guest room calls are completed in the same manner as calls to ordinary stations.
Service Conditions
1. The same station number cannot be assigned to more than one station in the NEAX2400 IPX.
2. Guest numbers must be contained within Tenant 1.
3. One-, two-,...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 213
Room Numbering R-17
Assignment Procedure
Note:If the data is assigned as “1”, only use commands AANP & AAST to assign Administration and Guest
Station Numbering Plan. If data “0” is assigned, use AANP & AAST for Administration Numbering Plan,
and AGNP & AGST for Guest Numbering Plan.
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX
160b
0Hotel Feature required (Fixed Data)
b
1Hotel Service kind (Fixed Data)
b
2Length of Room Status...

NEAX2400 IPX Hotel Feature Programming ManualPage 214NDA-24304, Issue 1
S-17 Split Access to Outgoing
S-17Split Access to Outgoing
General Description
This feature allows stations which are differentiated by Guest/Administration data, CLASS OF SERVICE -
INDIVIDUAL [C-15] data (Service Feature Class, Telephone Equipment Class, Route Restriction Class) or Day/
Night information to dial the same access codes but access different service features or trunk routes.
Operating Procedure
System data programming...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 215
Split Access to Outgoing S-17
 When the Numbering Plan Table is used in common for both Administration Stations and Guest Stations:
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX
160b
0Hotel Feature required (Fixed Data)
b
1Hotel Service kind (Fixed Data)
b
2Length of Room Status Memory
0/1 = 8 byte/24 byte
b
3Pattern of Key Arrangement on Hotel Console
(Refer toTable 7) (Usually, 00)
b
4
b5Guest Name Service
0/1 = Out/In Service
b...

NEAX2400 IPX Hotel Feature Programming ManualPage 216NDA-24304, Issue 1
S-32 Screening
S-32Screening
General Description
This feature provides the Attendant with a special SCRN key which lets them selectively extend calls which require
SCREENING, and process other calls while waiting for the called station to answer. This is especially helpful when
the Attendant is responding to a VIP call which requires special handling, but must also enter other loops because
other calls require attention.
Operating...