NEC Neax 2400 Ipx Hotel Feature Programming Manual

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 227
2nd Wake-up Call - Same Guest Station S-128
S-1282nd Wake-up Call - Same Guest Station
General Description
By combining with AUTOMATIC WAKE-UP [A-27] service, this service allows two wake-up calls to be set for a
Guest room.
Operating Procedure
The notice asking the Guest to call the Attendant when the Guest wants to set the second wake-up call should be
prepared in the Guest room. The Guest sees the notice and calls the attendant....

NEAX2400 IPX Hotel Feature Programming ManualPage 228NDA-24304, Issue 1
S-128 2nd Wake-up Call - Same Guest Station
Operating Procedure (cont’d)
2. Dial the wake-up time requested.
3. Dial the second wake-up set code.
4. Press theENTERkey. The display shows “2ND WAKE UP ENT (A).” or “2ND WAKE UP ENT (S).”
according to the service set code dialed.
5. Dial the Guest station number. The display shows the station number.
6. Press theENTERkey.
Note 1
a.) To set the second wake-up call for another Guest...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 229
2nd Wake-up Call - Same Guest Station S-128
Service Conditions (cont’d)
13. The information can be printed by the hotel printer either in one-line or two-line format. (The selection is
to be made in the hotel system parameters.) However, when cancelled automatically via MAID STATUS
[M-22] service or when called by the attendant in case of AUTOMATIC WAKE-UP - HOTEL
ATTENDANT ASSISTANCE [A-58] service (“ATT CALLED”), the information...

NEAX2400 IPX Hotel Feature Programming ManualPage 230NDA-24304, Issue 1
S-128 2nd Wake-up Call - Same Guest Station
Assignment Procedure
See [A-10] Assignment Procedure for programming initial Wake-Up.
STEP CMND BIT EXPLANATION
1AHSY
INDEX
163b
02nd Wake-Up Call Service
0/1 = Out/In Service
b
12nd Wake-Up Call Time Indication on the Console
0/1 = Out/In Service
b
22nd Wake-Up Call Cancel while the Console is connected to the target station
0/1 = Out/In Service
b
3Not used
b...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 231
Toll Terminal Access T-13
T-13Toll Terminal Access
General Description
This feature enables Guest stations to directly access toll trunks. Access may be arranged on a direct-dial or
attendant-assisted basis, depending on the associated Central Office.
Operating Procedure
1. The Guest station dials the toll access code (usually “8”).
a.) If direct-dial service is allowed, the Guest will receive dial tone and may place the call.
b.)...

NEAX2400 IPX Hotel Feature Programming ManualPage 232NDA-24304, Issue 1
T-21 Timing Start
T-21Timing Start
General Description
This feature allows single-digit and multi-digit stations to use the same numbering plan levels by providing a
predetermined time delay between the completion of dialing and the start of ringing. By pressing the # or * key after
dialing the station number, the station user will not have to wait for ring start. By pressing theSTARTkeyonthe
Console, the attendant will not have to...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 233
Timing Start T-21
Assignment Procedure
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX
129b
0Register Interdigit Timer:
Miscellaneous Timer Counter (MTC) is to be
assigned a value from 0 Hex to F Hex (0-15).
The interval between dialed digits.
Timer Value Setting is MTC x 2 sec.
Note:
When this data is 00 Hex,
default data is automatically
setto6sec.
b1
b2
b3
b4
Not used b5
b6
b7
2SYS1
ASYD
INDEX
161b
0Don’t Disturb Override key on...

NEAX2400 IPX Hotel Feature Programming ManualPage 234NDA-24304, Issue 1
T-21 Timing Start
Note 1:Do not assign “*” or “#” as last digit of feature access code. No station may use “*” or “#” in numbering.
Note 2:Room Cutoff (RSC 13)
Do Not Disturb (RSC 14)
Room Cutoff and Do Not Disturb (RSC 15)
3SYS1
ASYD
INDEX
170b
0Room status data (b2,b1,b0)tobesetatthetimeofCheckout
b
2b1b0b2b1b0
00 0=– 0 1 0=Cleaned
0 0 1 = To be Cleaned 0 1 1 = Ready for Occupancy
Do not assign other data. b1
b2
b3Restriction at...

NEAX2400 IPX Hotel Feature Programming Manual
NDA-24304, Issue 1Page 235
Voice Mail Service Via Message Center Interface (MCI) V-16
V-16Voice Mail Service Via Message Center Interface
(MCI)
General Description
Voice mail service is available for Guest and Administration Stations through the Message Center Interface (MCI)
in the NEAX2400 IPX Hotel System. This capability allows the integration of a customer-provided voice mail
system, using an RS-232C interface. Guest calls are Call Forwarded - All...

NEAX2400 IPX Hotel Feature Programming ManualPage 236NDA-24304, Issue 1
V-16 Voice Mail Service Via Message Center Interface (MCI)
Service Conditions (cont’d)
3. Display operations for Console, Front Desk Terminal, and PMS are not performed (i.e. check-in,
checkout, room change recovery do not operate).
4. The NEAX2400 IPX will be notified of message waiting lamp on/off requirements by the Voice Mail
equipment via MCI.
5. The message waiting lamp control feature from MCI is not performed for Suite Room...