NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 308NDA-24297, Issue 1
D-90D Delayed Ringing - Dterm
General Description (cont’d)
DELAYED RINGING may also be used for calls terminated to single-line telephone appearances on a Dterm.Calls
to single line appearances that are not answered within a preprogrammed time will ring on the next station in
sequence.
A call rings on Single Line Station A. If Station A does not answer within a preprogrammed time, the call also rings
on D
termStation B. If the call is not...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 309
Delayed Ringing - DtermD-90D
Programming
AKYD- Assign the following parameters to stations that will have delayed ringing:
TN: Tenant Number
STN: Station Number
TP: Type of D
term:0/1
RING: 0: No Ringing
1: Ringing All Lines
2: Ringing on Prime Line only
3: Flexible Ring Assignments (Enables RG Parameters)
PL TN STN:Prime Line Tenant and Station Number
KYN: Key Number (1-40)
KYI: Service Index
0: Key Not Used
1: Feature Key
2: Multi-line...

NEAX2400 IPX Feature Programming ManualPage 310NDA-24297, Issue 1
D-114 Delay Announcement - Attendant
D-114  Delay Announcement - Attendant
General Description
This feature provides a recorded announcement to the incoming trunk caller waiting to be answered by the
Attendant. This feature is divided into the following two types, depending on the time when the call is connected
with the announcement trunk.
The call is connected to announcement trunk immediately after terminating to the Attendant Console....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 311
Delay Announcement - Attendant D-114
Service Conditions (cont’d)
5. At the time of DAY/NIGHT mode changeover, the call connected to the announcement will be released,
and the calling party receives reorder tone. A call will be released as follows,according to the incoming
trunk type:
a.) When a call terminates from a trunk where trunk release cannot be supervised, the trunk will be
released forcefully. (Night Transfer station cannot be...

NEAX2400 IPX Feature Programming ManualPage 312NDA-24297, Issue 1
D-114 Delay Announcement - Attendant
Service Conditions (cont’d)
5. When Multiple Playback is selected, additional DAT channel is required for the second announcement,
even if the second announcement has the same contents as the first one.
6. A maximum of 10 incoming trunk calls can be connected to a single DAT trunk at one time for sending a
prerecorded message from the beginning to the called parties.
7. The maximum programmable channels...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 313
Delay Announcement - Attendant D-114
Service Conditions (cont’d)
16. CALL QUEUING [C-9] and CALL WAITING LAMP [C-13] services are available when this service is
activated.
17. The calling party cannot receive the message if the restriction between the incoming trunk and the
announcement trunk is not cleared.
18. When this service is allowed in system data, the ATTENDANT OVERFLOW [A-105] feature cannot be
activated.
19. When the external...

NEAX2400 IPX Feature Programming ManualPage 314NDA-24297, Issue 1
D-114 Delay Announcement - Attendant
Programming (cont’d)
TC=3.2 sec. MTC=0-15
SYS1, Index 244. b5=1 (Announcement is provided immediately after the ring back tone)
SYS1, Index 245. Timer for Delay Announcement - Attendant (Duration of Music on Hold)
Timer for duration of RBT = TC X MTC
TC=3.2 sec. MTC=0-15
SYS1, Index 246. Attendant Delay Announcement
0/1= Single Playback/Multiple Playback
STEP 2:ARTD- Assign the route data of the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 315
Direct Station Selection (DSS) Console D-149
D-149  Direct Station Selection (DSS) Console
General Description
A Direct Station Selection (DSS) Console may be connected to each Dterm. The DSS keys can be used as line keys
or feature keys.
Operating Procedure
Refer to the User Guide.
Service Conditions
1. The DSS console has 60 keys, each with one or two lamps.
2. The DSS console has following two operating functions:
a.) DSS/BLF function...

NEAX2400 IPX Feature Programming ManualPage 316NDA-24297, Issue 1
D-149 Direct Station Selection (DSS) Console
Service Conditions (cont’d)
6. When the user calls the DSS station by SPEED CALLING - ONE TOUCH, or transfers the call to the DSS
station, and the DSS station is the member of the UCD [U-1] or station hunting group, the call follows the
UCD or the hunting operation. (If the MCI is valid, the message is sent out.)
7. The user can recognize the idle/busy status of the accommodated stations by the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 317
Direct Station Selection (DSS) Console D-149
Service Conditions (cont’d)
3. The 48th key and after can be used only as the feature keys, not as the line keys. (These keys do not have
the green lamps, therefore, I-used or I-hold cannot be indicated.)
4. Only 8-button and 16-button D
termcan be used when using the DSS console in the ADM mode.
5. The D
termto be connected to the DSS console should be accommodated in the same circuit card as...