NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 338NDA-24297, Issue 1
E-1D Executive Right-of-Way - Dterm
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note
STEP 7:ANPDL- Assign first digit of access code for EXECUTIVE RIGHT-OF-WAY.
STEP...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 339
Elapsed Time Display - DtermE-3D
E-3D  Elapsed Time Display - Dterm
General Description
This feature provides an LCD display of the time elapsed while a Dtermis connected to any trunk.
Operating Procedure
No manual operation is required.
Service Conditions
1. The ELAPSED TIME is displayed in the eight left-side positions of the LCD display.
2. The ELAPSED TIME can reach a maximum of 9 hours, 59 minutes and 59 seconds. After that time,...

NEAX2400 IPX Feature Programming ManualPage 340NDA-24297, Issue 1
E-4D Exclusive Hold - Dterm
E-4D  Exclusive Hold - Dterm
General Description
This service feature allows a user to place a call on hold and to exclude all other users from retrieving the held call.
Operating Procedure
While a call is in progress
1. Press the HOLD key twice; the LCD displays:
                                                                     Held Station or Trunk
2. To return to the held call, press the held line key; the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 341
Emergency Call E-11
E-11 Emergency Call
General Description
This feature allows a user to make an EMERGENCY CALL by dialing a special telephone number (emergency
telephone number). Even if the calling station goes on-hook, the calling station is recalled and the speech path is
maintained until the emergency telephone goes on-hook. When a station dials the emergency telephone number, a
system message is printed out to report the EMERGENCY...

NEAX2400 IPX Feature Programming ManualPage 342NDA-24297, Issue 1
E-11 Emergency Call
Service Conditions (cont’d)
13. When the emergency station is busy, CALL BACK [C-1] to the emergency station is effective (no printout
is performed).
14. When the emergency station is busy, CALL WAITING - ORIGINATING [C-31] and CALL WAITING
- TERMINATING [C-12] are effective, but this service feature is not available. However, when a 2-way
call is made between an emergency station and another station, CALL BACK [C-1] is...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 343
E911-ANI Unified Number Of Digits E-18
E-18  E911-ANI Unified Number Of Digits
General Description
This service unifies the number of ANI information digits sent out by E911-ANI service.
Operating Procedure
The operating procedure is the same as for a normal outgoing connection.
Service Conditions
1. The ANI function for E911 outgoing connections is the same as in previous E911-ANI service and is
applicable to the following connections:...

NEAX2400 IPX Feature Programming ManualPage 344NDA-24297, Issue 1
E-18 E911-ANI Unified Number Of Digits
Service Conditions (cont’d)
If ANI data is unassigned:
KP-1-ST
5. An independent route is required for E911 interface.
6. After the caller’s number is sent to the distant office by E911-ANI, it takes some time until a speech path
is established.
7. Sending data is considered to be not assigned if:
a.) Service version data specifies that Unified Number of Digits is provided,
b.) No data is assigned...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 345
Expanded Multiple Line Operation - DtermE-26
E-26  Expanded Multiple Line Operation - Dterm
General Description
This feature allows operation of whichever lines from ELC card(s) in the same IMG or in different IMGs in the same
node, as a Dterm’s programmable Multiple Lines (My Line + Prime Line/Sub Lines). While Multiple Line Operation
-Dterm[M-20] only allows such a programming within the reach of ELC card(s) in the same IMG, this...

NEAX2400 IPX Feature Programming ManualPage 346NDA-24297, Issue 1
E-26 Expanded Multiple Line Operation - Dterm
Service Conditions (cont’d)
b.) PA-16ELCJB-B, SW10, Element 1 = OFF:A Dterm, accommodated on this card, and the other
Lines (other analog telephone/Dterm)canbein
different IMGs (but in the same node). For more
details on the PA-16ELCJ-B circuit card, refer to the
NEAX2400 IPX Circuit Card Manual.
Note:Even when Element 1 of SW10 is ON, data programming for this feature (Multiple Lines beyond...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 347
Expanded Multiple Line Operation - DtermE-26
Interactions (cont’d)
Serial Call [S-15]
Serial Call - Loop Release [S-64]
Serial Call - CCIS [S-52]
Serial Call - D
term[S-127]
Executive Right-of-Way [E-1, 1D]
Call Back [C-1, 1D]
Message Reminder [M-19, 19D]
Brokerage - Hot Line [B-6]
Split Call Forwarding [S-99]
Call Waiting - Terminating [C-12]
CallWaiting-Answer-D
term[C-27D]
Call Waiting - Originating [C-31]
Note:Boss-Secretary features...