NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 368NDA-24297, Issue 1
F-35 Flexible Routing - FCCS
F-35  Flexible Routing - FCCS
General Description
With this feature, an FCCS trunk call can automatically be routed via a non-FCCS trunk (C.O. or Tie Line), if all
the FCCS trunks are busy or a Data Link Failure occurs at the FCH card.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is activated when all FCCS trunks are busy, a transmission failure occurs, or FCCS Link...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 369
Flexible Routing - FCCS F-35
Interactions (cont’d)
Note 3:The display is changed depending on the specification of ACIS.
Note 4:Has priority over the FLEXIBLE ROUTING - FCCS service. FLEXIBLE ROUTING - FCCS is activated
only when the FCCS trunk for the destination station is busy.
Note 5:A trunk is used after the call encounters station busy between the stations in the FCCS network.
Note 6:Available only at the time of the data assignment...

NEAX2400 IPX Feature Programming ManualPage 370NDA-24297, Issue 1
F-36 FCCS Networking via IP
F-36  FCCS Networking via IP
General Description
This feature allows the system to exchange both speech and FCCS signals over Internet/Intranet. To establish/
release a call, the following two connection patterns can be selected:
IPTRK Point-to-Point Connection: For both speech and FCCS signal channels, an IPTRK circuit card
is used. At this time, the IPTRK cards in the self-node and each of
its connected...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 371
FCCS Networking via IP F-36
Operating Procedure
No manual operation is required.
Service Conditions
FCCS over IPTRK
1. To send/receive voice information, each node shall use IPTRK circuit card(s). At this time, the IPTRK
cards in the self-node and its connected node(s) can be either in 1-to-1 ratio, respectively (called point-to-
point connection), or in 1-to-n [n=2 or more] relations (called point-to-multipoint connection). For point-...

NEAX2400 IPX Feature Programming ManualPage 372NDA-24297, Issue 1
F-36 FCCS Networking via IP
Service Conditions (cont’d)
10. IPTRK-related tandem connection is not available.
11. Any service not available on the FCCS network, is not available with this feature.
12. Tandem Path through function is not provided.
13. This feature supports QoS (Quality of Service) function.
14. When a system message indicates TCP link failure due to data congestion on the router or IP network, a
call cannot be made via an...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 373
FCCS Networking via IP F-36
Service Conditions (cont’d)
FCCS via IP using Cisco router
1. DTI (1.5M and 2.0M) interface is used as speech channel.
2. The FCH-FGH card is used as a signal channel. Only a single FCH-FGH card can be connected to a router.
Accordingly, redundant configuration of FCH-FGH is not available.
3. An interface number is assigned to each speech channel and is changed into the TCP/IP port number
between PBX and router...

NEAX2400 IPX Feature Programming ManualPage 374NDA-24297, Issue 1
F-36 FCCS Networking via IP
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
 Note
The data programming for Point-to-Point connection and Point-to-Multipoint connection is...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 375
FCCS Networking via IP F-36
FCCS Programming (cont’d)
Note:When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN. 

NEAX2400 IPX Feature Programming ManualPage 376NDA-24297, Issue 1
G-2 Group Calling
G-2 Group Calling
General Description
This feature allows a user to dial certain frequently called stations within an NEAX2400 IPX group using an easily
remembered number. The same number can be assigned to different user groups. The group call can initiate CALL
WAITING - ORIGINATING [C-31] to a busy station.
Operating Procedure
To initiate a group call
1. Lift the handset; receive dial tone.
2. Dial the GROUP CALLING...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 377
Group Calling G-2
Service Conditions (cont’d)
10. To initiate CALL WAITING - ORIGINATING [C-31] with GROUP CALLING, a Dtermmust:
a.) Dial the CALL WAITING - ORIGINATING [C-31] access code.
b.) Dial the GROUP CALLING access code (maximum 3 digits).
c.) Dial the GROUP CALLING station code (1 or 2 digits).
d.) CALL WAITING-ORIGINATING access code is not needed if automatic is set.
Interactions
1. As an example of a GROUP CALLING application,...