NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 358NDA-24297, Issue 1
F-6 Faulty Trunk Report
F-6 Faulty Trunk Report
General Description
This feature allows a station to report a noisy or faulty trunk number by dialing a special access code before hanging
up. The FAULTY TRUNK REPORT consists of a trunk number, telephone number, associated time division switch
and reported time. This information is displayed at the MAINTENANCE ADMINISTRATION TERMINAL
(MAT) [M-18] and/or system printer.
Operating Procedure
To...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 359
Forced Account Code F-7
F-7  Forced Account Code
General Description
This feature is a variation of the ACCOUNT CODE [A-18] feature, which makes it mandatory to enter an
ACCOUNT CODE (up to 10 digits) for all outgoing calls. The account code must be dialed before dialing the
outgoing number. Calls are processed only when the dialed account code is valid.
The FORCED ACCOUNT CODE can be masked on the D
termdisplay if necessary using the...

NEAX2400 IPX Feature Programming ManualPage 360NDA-24297, Issue 1
F-7 Forced Account Code
Service Conditions (cont’d)
Note:There are two methods of FORCED ACCOUNT CODE assignment. These methods are Full
Implementation and the Check Sum method. In the Full Implementation method, the whole FORCED
ACCOUNT CODE is assigned in the AATC command and System Data 1, Indexes 12, 13, & 14 are assigned
00H. In the Check Sum method, partial assignment for each FORCED ACCOUNT CODE is assigned in the
AATC command. The...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 361
Forced Account Code F-7
Programming (cont’d)
Note:Bit 0 through bit 7 may be used when 8-digit FORCED ACCOUNT CODES are assigned in the AATC
command.
System Data 1, Index 13. Each bit in Index 13 directly correlates to a digit in the FORCED
ACCOUNT CODE assigned in AATC, and will determine the second digit of the Check Sum method.
Again pick any bits, 0 to 4, but not the same combination of bits as picked in Index 12.
System Data 1, Index...

NEAX2400 IPX Feature Programming ManualPage 362NDA-24297, Issue 1
F-7 Forced Account Code
Programming (cont’d)
Note:Digits 39 determined by the Check Sum method will be unique to the FORCED ACCOUNT CODE 26428.
In other words, 26428 will not be followed by any digits other than 39.
System Data 1, Index 43, bit 2. Is service set tone sent after FORCED ACCOUNT CODE ASPA
feature access code? 0/1: No/Yes.
System Data 1, Index 93, bit 6. Are the AMND tables Separate or Common for tenants in the system?
0/1:...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 363
Flexible Assignment of Function Buttons F-17
F-17  Flexible Assignment of Function Buttons
General Description
This feature allows Dtermfunction (feature) buttons (REDIAL, FEATURE, SPEAKER, CONF, ANSWER,
RECALL, HOLD, and TRANSFER) to be flexibly assigned on each individual Dterm.
Function (feature) buttons are programmed through the Maintenance Administration Terminal (MAT) and are part
of system data.
Service Conditions
1. A feature...

NEAX2400 IPX Feature Programming ManualPage 364NDA-24297, Issue 1
F-31 Follow Phone
F-31 Follow Phone 
General Description
This feature allows individual station data of a terminal to be exchanged with another without the assistance of
MAT. The result of the exchange is printed out in the system message. The exchange of terminal data by this service
is called SWAP service. The following information is included in the system message:
a.) Successful activation: Station data change notice.
b.) Unsuccessful...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 365
Follow Phone F-31
Service Conditions (cont’d)
5. Following data assigned to each Dtermwill be cleared when this service is activated:
DO NOT DISTURB [D-11]
LAST NUMBER CALL [L-6]
MESSAGE REMINDER [M-19]
SAVE AND REPEAT [S-24]
6. This service is not available for the following stations:
a.) Night station (ACSI)
b.) HOT LINE [H-1] station
c.) HOUSE PHONE [H-2]
d.) Data line, or D
termthat has a data line assigned
e.) Station setting/being...

NEAX2400 IPX Feature Programming ManualPage 366NDA-24297, Issue 1
F-31 Follow Phone
Service Conditions (cont’d)
12. When this service is activated, the key information of Dterm, which has the target station as a multi-line
will be changed automatically. For example:
13. If the multi-line LED of D
termis lit (busy) when the station swaps, the line LED key may not light
immediately after the service is activated. The LED light normally after the user goes on-hook.
14. For the stations that belong to the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 367
Follow Phone F-31
Service Conditions (cont’d)
20. When activating this service, swap of the Speed Calling - One Touch key data start upon replacement of
the handset. It takes approximately 42 seconds for the Speed Calling key data to swap, and during this
time, Follow Phone Service and Speed Calling - One Touch operations are restricted.
21. After this service is activated, and if DM load reset is activated before the data is backed up to...