NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 378NDA-24297, Issue 1
H-1 Hotline
H-1 Hotline
General Description
This feature permits a pair of station sets to be associated with one another on an automatic ringdown basis.
Operating Procedure
1. Station A lifts the handset.
2. Station B is rung.
3. Station B lifts the handset; the conversation proceeds.
Service Conditions
1. If both phones in a hotline pair are equipped with dials, either one may transfer a hotline call to another
station.
2. There is no...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 379
Hotline H-1
Interactions (cont’d)
2. CONSULTATION HOLD [C-17]: The HOTLINE station may put the destination station on
CONSULTATION HOLD [C-17]. In this state, the HOTLINE station may make an outgoing call, and is
therefore affected by CLASS OF SERVICE-INDIVIDUAL [C-15].
3. CALL WAITING-ORIGINATING [C-31]: A HOTLINE will not be allowed to camp-on to a busy
destination station.
4. If the connecting station is also a HOTLINE station, then...

NEAX2400 IPX Feature Programming ManualPage 380NDA-24297, Issue 1
H-2 House Phone
H-2 House Phone
General Description
This feature allows selected stations to reach the ATTENDANT CONSOLE [A-1] by going off-hook.
Operating Procedure
To reach the ATTENDANT CONSOLE [A-1]:
1. The HOUSE PHONE user lifts the handset. The Attendant is called automatically.
2. The Attendant answers.
3. The Attendant connects the user to the desired station or trunk.
Service Conditions
1. Attendant Console indications will appear...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 381
Hands-free Answer Back - DtermH-4D
H-4D  Hands-free Answer Back - Dterm
General Description
This feature allows the user to respond to a VOICE CALL - Dterm[V-2D] without lifting the handset.
Operating Procedure
To answer an incoming call
1. Lift the handset and press the line key to answer the call.
2. Press the feature key and“1”; the MIC LED lights.
3. Press the feature key and“5”to select HANDS-FREE operation.
4. Press the SPEAKER key...

NEAX2400 IPX Feature Programming ManualPage 382NDA-24297, Issue 1
H-5D Hands-free Dialing/Monitoring - Dterm
H-5D  Hands-free Dialing/Monitoring - Dterm
General Description
This feature allows the Dtermuser to dial or monitor and call without lifting the handset.
Operating Procedure
To dial a call HANDS-FREE
1. Press the SPEAKER key; receive dial tone.
a.) Dial the desired number.
b.) When the called party answers, lift the handset.
To monitor a call HANDS-FREE
1. When placed on hold, press the SPEAKER...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 383
Hotline - Outside H-9
H-9 Hotline - Outside
General Description
This feature allows a user to access an outside destination by going off-hook or selecting the HOTLINE-OUTSIDE
[H-1] line/feature key and automatically dialing a SPEED CALLING-SYSTEM [S-3] number.
Operating Procedure
To place a HOTLINE - OUTSIDE call using a single-line telephone
1. User lifts handset.
2. PBX automatically selects a trunk and dials the outside number.
3....

NEAX2400 IPX Feature Programming ManualPage 384NDA-24297, Issue 1
H-9 Hotline - Outside
Interactions 
SPEED CALLING-SYSTEM [S-3] must first be provided.
Programming
STEP 1:ASYD- System Data 2, Index 1, Bit 7. Does TOLL RESTRICTION apply to SPEED CALLING-
SYSTEM [S-3]? 0/1: Yes/No. If TOLL RESTRICTION applies, construct an RSC that will allow the
station access to the outgoing number.
STEP 2:ASFC- Construct a Service Feature Class that allows Service Feature Index (SFI) 12; SPEED
CALLING-SYSTEM [S-3]....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 385
Hotline - Outside H-9
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
 Note 1
AHLSN- This data must be assigned to the NCN:
UGN: User Group Number of the calling party
TELN:...

NEAX2400 IPX Feature Programming ManualPage 386NDA-24297, Issue 1
I-1 Immediate Ringing
I-1 Immediate Ringing
General Description
This feature causes called stations to ring immediately upon establishment of connections.
Operating Procedure
No manual operation is required.
Service Conditions
1. Ringing is applied to a called station as soon as the switch has determined that the station is idle. There is
no delay caused by waiting for a ring cycle.
2. This feature applies to STATION-TO-STATION [S-11],...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 387
Incoming Call Identification I-2
I-2 Incoming Call Identification
General Description
This feature allows an ATTENDANT CONSOLE [A-3] to visually identify the type of service and/or trunk group
that is arriving or waiting to be answered.
Operating Procedure
No manual operation is required.
Service Conditions
1. A flashing lamp indicates a call waiting to be answered.
2. A steady lamp indicates an answered call.
3. A limit of 12 lamp and...