NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 298NDA-24297, Issue 1
D-31 Delay Announcement - UCD
Programming (cont’d)
CNT: Number of Announcement Trunks
RT: Route Number
TK: Trunk Number
The Tenant and Station parameters will be prompted only if ASYD calls for separate announcements
for UCD groups.
The Delay timer, DLYT, is the time that the Delay Announcement trunk will ring and collect other
incoming calls that will listen to the DELAY ANNOUNCEMENT-UCD.
The Message timer, MSGT, should include both the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 299
Dual Hold - DtermD-32D
D-32D  Dual Hold - Dterm
General Description
This feature allows two Dterms to simultaneously be placed on hold. This allows the held parties to answer or
originate a call from a subline appearance or the idle prime line.
Operating Procedure
To place a call in a DUAL HOLD-Dterm condition
1. When two Dterms are connected, either Dtermuser can press the pre-assigned HOLD key and place the
other Dtermon hold.
2. If the...

NEAX2400 IPX Feature Programming ManualPage 300NDA-24297, Issue 1
D-32D Dual Hold - Dterm
Service Conditions (cont’d)
BUSY VERIFICATION [B-3]
ATTENDANT CAMP-ON [A-1]
EXECUTIVE RIGHT-OF-WAY [E-1]
CALL WAITING-ORIGINATING [C-31]
CALL WAITING-TERMINATING [C-12]
Programming
ASYD- System Data 1, Index 144. Recall timer for EXCLUSIVE, NON-EXCLUSIVE HOLD.
Assign data 00H for 30 seconds. (RAM default data is 3FH.)
System Data 2, Index 12, Bit 0. Is Automatic Recall Ringing provided on a per-tenant basis? 0/1:...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 301
Dial Intercom D-87
D-87 Dial Intercom
General Description
This feature gives multiple Dtermusers the ability to simultaneously call any other member of the intercom group,
regardless of their idle or busy status. An intercom group member can override another intercom station in a two-
party intercom connection. This service is referred to as an Intercom Bridge.
Operating Procedure
To originate
1. The intercom station presses the DICM key...

NEAX2400 IPX Feature Programming ManualPage 302NDA-24297, Issue 1
D-87 Dial Intercom
Operating Procedure (cont’d)
PRIME LINE PICK UP-Dterm [P-13D]
The Dtermmay be programmed to seize the incoming call on the AUTOMATIC, MANUAL, or DIAL INTERCOM
lines before the Prime Line. If two incoming calls terminate simultaneously to both the Prime Line and the DIAL
INTERCOM line, when the user goes off-hook, PRIME LINE PICKUP-D
term[P-13D] will seize the DIAL
INTERCOM line before the Prime Line. If only the Prime...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 303
Dial Intercom D-87
Service Conditions (cont’d)
16. The display on the Dtermis as follows:
a.) Calling
b.) Called Station AnswersICM                                                      XX
                    (Time Display)  Dial Intercom Number of the Calling Station
* Display appears for 10 seconds when the DICM line is
preselected
Called
Station60 IPM 
flashing
ICM                                                      XX...

NEAX2400 IPX Feature Programming ManualPage 304NDA-24297, Issue 1
D-87 Dial Intercom
Service Conditions (cont’d)
c.) Intercom Bridge
d.) Intercom Bridge Restriction
17. To answer a call terminated to the INTERCOM line while the Prime Line is busy, press an INTERCOM
line key.
18. The DIAL INTERCOM ringing by an incoming call is interrupted while the MANUAL SIGNALING [M-
47] signal is being sent out.
19. While a call is in progress on a multi-line, the AUTOMATIC INTERCOM line, or MANUAL
INTERCOM line,...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 305
Dial Intercom D-87
Programming (cont’d)
STEP 2:ADIM- Assign the following data:
MG: Module Group
G-ID: Group ID Number per MG
N: Number of Digits of Dial Intercom Group (0/1)
0: 1 digit
1: 2 digits
BCR: Bridge Call Restriction (0/1)
0: Restricted
1: Allowed
TN: Tenant Number
ICMCT Number of Intercom Stations (2-64) (actual number to dial)
ICM STN:Intercom Station Number
STEP 3:AKYD- Assign an Intercom Line to the station according to the...

NEAX2400 IPX Feature Programming ManualPage 306NDA-24297, Issue 1
D-90D Delayed Ringing - Dterm
D-90D  Delayed Ringing - Dterm
General Description
ThisfeatureallowsaDtermto receive an incoming ringing signal after a predetermined time.
In Boss/Secretary service, a call terminating on the bosss line first rings at the secretarys station. If the secretary
does not answer within a preprogrammed time, the boss station will also ring. This service is convenient when many
lines terminate on a secretarys phone,...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 307
Delayed Ringing - DtermD-90D
General Description (cont’d)
This feature may also be used in a similar way to CALL FORWARDING - DONT ANSWER [C-3] or STATION
HUNTING [S-7, 8, 9].
A call rings on Station A. If Station A does not answer within a preprogrammed time, the call also rings on Station
B. If the call is not answered within the second preprogrammed time, the call also rings on Station C. If the call is
not answered within the third...