NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 258NDA-24297, Issue 1
C-157 Calling Party Number - Name Assignment and Display
C-157  Calling Party Number - Name Assignment and 
Display
General Description
This feature allows a user to assign the desired name for the calling number, which is provided by Central Office,
CCIS or ISDN feature, using the MAT command. The assigned name is displayed on the LCD of the Dtermand the
Desk Console.
Operating Procedure
No manual operation is required.
Service...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 259
Calling Party Number - Name Assignment and Display C-157
Service Conditions (cont’d)
12. The Display patterns are shown below:
13. Characters of 8-bit ASCII can be displayed for this feature.
14. When the feature key which assigned FKY = 113 via AKYD is pressed, the display pattern on the LCD
(assigned by the ASYD command) changes according to the following conditions:
When My Line is Prime Line, Call ID Change Display Key is effective...

NEAX2400 IPX Feature Programming ManualPage 260NDA-24297, Issue 1
C-157 Calling Party Number - Name Assignment and Display
Service Conditions (cont’d)
18. The trunk mentioned below is available as for analog COT:
19. When this feature is activated via FCCS, the same data should be set to all nodes.
Programming
STEP 1:ASYD- System Data 1, Index 241, b6: Assign the data when the length of Caller ID exceeds the limit:
0/1 = Only the former/latter part of data appears on the LCD.
Index 390,
b0: Assign the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 261
Call Trace C-160
C-160 Call Trace
General Description
This feature enables the output of System Message [26-R], that gives information on a malicious call (kind of call,
number of calling terminal, etc.) originated from a station/trunk. The feature is made available when an access code
is dialed or the“Call Trace”key is pressed by the called user.
Note:For details on the System Message [26-R], see the NEAX2400 IPX System Operations and...

NEAX2400 IPX Feature Programming ManualPage 262NDA-24297, Issue 1
C-160 Call Trace
Operating Procedure (cont’d)
Note:Details on LCD display (for the DtermSeries E only) are as follows:
24 digits display of a Dterm Series E
When the CALL TRACE is set:
When the CALL TRACE is assigned to the soft key:
When HELP key (Soft Key) is pressed:
Service Conditions
1. This feature is made available via the stations, to which the following data is assigned via the ASFC
command [SFI = 170 (Call Trace), RES = 1...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 263
Call Trace C-160
Service Conditions (cont’d)
d.) The maximum digits for each data are as follows:
e.) When the called station does not have the telephone number, the FPC/Telephone Number/UGN
data is output as“0”.
f.) When the calling party is the station which does not have the telephone number, the Tenant
Number/FPC/Telephone Number/UGN data is output as“0”. The kind of call is output as“10”.
g.) If the number of the trunk call (Caller...

NEAX2400 IPX Feature Programming ManualPage 264NDA-24297, Issue 1
C-160 Call Trace
Programming (cont’d)
STEP 4:AKYD- Optional. Assign the CALL TRACE data to a Feature Key on the Dterm, FKI = 1 (Feature
Key), FKY = 129 (CALL TRACE).
STEP 5:ADSL- Optional. Assign the following to use a Soft Key on the D
termSeries E for CALL TRACE:
SKP: 0 - 15 (Soft Key Pattern)
SN = 1 [DT], 4 [Communication in Progress] (Status Number)
SKN: 1 - 16 (Soft Key Number)
FKY = 129 (CALL TRACE)
STEP 6:ADKS- Assign the following...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 265
Consultation Hold Release C-169
C-169 Consultation Hold Release
General Description
This feature enables a station, connecting to a second call while the station has been holding (consultation hold) an
original call (including ADD-ON CONFERENCE-8 PARTY [A-121] member), to disconnect the second call
forcibly by pressing DISC key for D
termonce/going switch hook flash for analog station/PS twice. After that, the
second call is released, and...

NEAX2400 IPX Feature Programming ManualPage 266NDA-24297, Issue 1
C-169 Consultation Hold Release
General Description (cont’d)
MUX
Station A 
 (H O LD ) 
Station B 
 (H O LD )
Station CAfter station B presses 
         DISC key
After station B presses 
          DISC key
MUX
Station A
Station B
Station C 
   (Idle)
MUX
Station A
Station B
Station C 
   (Idle)
ELC ELC
 ELC
MUX
Station A
Station B
Station C 
 (HOLD) ELC
CFT
When Station B presses CONF key before pressing
Note Note
Situation 2: When Station...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 267
Consultation Hold Release C-169
General Description (cont’d)
Operating Procedure
See General Description.
Service Conditions
1. This feature is available when System Data 1 Index 803 Bit 1 = 1 is assigned.
2. When there is a call terminated at Chinese specification MFC trunk in calls related to this feature, this
feature is not available.
3. ISDN terminal equipment cannot be applied to operating station of this feature.
After station B...