NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 208NDA-24297, Issue 1
C-29 Call Park
Service Conditions (cont’d)
BUSY VERIFICATION [B-3]
CALL WAITING - ORIGINATING [C-31]
CALL WAITING - TERMINATING [C-12]
EXECUTIVE RIGHT-OF-WAY [E-1, E-1D]
10. A station in an ATTENDANT-CONTROLLED CONFERENCE [A-2] cannot be parked.
11. There is no limit to the number of calls that can be parked simultaneously within a system.
12. A parked call will recall to the station that has set the CALL PARK. The recall timer is...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 209
Call Park C-29
Programming
STEP 1:ASYD- System Data 1, Index 142. For CALL PARK recall, the Miscellaneous Timer Counter is
assigned in bits 0-3. The Timer Class is assigned in bits 4-6. Timer Class of 3=2 seconds. Timer
Counter of 4=30 seconds.
System Data 2, Index 1, bit 0 & 1. CONSULTATION HOLD - ALL CALLS [C-17] allowed or
denied. 00: Denied; 01: Originating and Terminating Calls allowed, Tandem Call Denied; 11: All calls
allowed.
STEP...

NEAX2400 IPX Feature Programming ManualPage 210NDA-24297, Issue 1
C-29 Call Park
FCCS Programming (cont’d)
Note 1:When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN.
Note 2:System timers may be set on a network basis in ASYDN. 

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 211
Call Pickup - Direct C-30
C-30  Call Pickup - Direct
General Description
This feature allows a user to pick up a call to any other station in the system by dialing a specific CALL PICKUP-
DIRECT code.
Operating Procedure
To pick up an incoming call
1. Lift the handset; receive dial tone.
2. Dial the CALL PICKUP - DIRECT code; receive special dial tone.
3. Dial the specific telephone number to be picked up; incoming call is connected to...

NEAX2400 IPX Feature Programming ManualPage 212NDA-24297, Issue 1
C-30 Call Pickup - Direct
Programming (cont’d)
STEP 2:ANPD- Reserve a number level for feature access. Assign for Normal (N), Hooking (H), and Busy
(B).
STEP 3:ASPA- Assign an access code to CALL PICKUP-DIRECT, SRV = SSC (Service Code), SID = 35 for
Connection Status Index (CI) of Normal (N).
STEP 4:ASFC- Assign a Service Feature Class that allows SFI 29 to the stations.
FCCS Programming 
This data setting describes only the additional or...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 213
Call Waiting - Originating C-31
C-31  Call Waiting - Originating
General Description
This feature provides selected stations with Camp-On capability to a busy internal station.
Operating Procedure
To activate
1. Dial the desired telephone number; receive busy tone.
2. Switch hook flash, receive special dial tone, dial the CALL WAITING - ORIGINATING code; or press
theCWkeyontheD
term.
3. Receive Call Waiting ringback tone. Call Waiting...

NEAX2400 IPX Feature Programming ManualPage 214NDA-24297, Issue 1
C-31 Call Waiting - Originating
Service Conditions (cont’d)
9. When the called station goes on-hook, the Call Waiting ringback tone changes to normal ringback tone to
the calling station.
10. CALL WAITING-ORIGINATING cannot be activated while in CONSULTATION HOLD [C-17] mode.
11. CALL WAITING-ORIGINATING cannot be used in conjunction with DIAL ACCESS TO
ATTENDANT [D-2].
12. CALL BACK [C-1] activation is denied if a call is waiting at the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 215
Call Waiting - Originating C-31
Service Conditions (cont’d)
EXCLUSIVE HOLD - Dterm[E-4D]
EXECUTIVE RIGHT-OF-WAY [E-1, E-8]
NON-EXCLUSIVE HOLD - D
term[N-7D]
OFF-HOOK QUEUING [O-7]
OUTGOING TRUNK QUEUING [O-2, O-2D]
PRIVACY - D
term[P-14D]
PRIVACY RELEASE [P-18]
THREE-WAY CALLING [T-2, T-2D]
VOICE CALL - D
term[V-2D]
21. The following service features take precedence over CALL WAITING - ORIGINATING:
CALL FORWARDING - ALL CALLS [C-5]
CALL...

NEAX2400 IPX Feature Programming ManualPage 216NDA-24297, Issue 1
C-31 Call Waiting - Originating
Programming (cont’d)
STEP 2:ANPD- Reserve a number level for feature access. Assign for Normal (N), Hooking (H), and Busy
(B). Assign NND in accordance with a predetermined numbering plan.
STEP 3:ASPA- Assign an access code to CALL WAITING-ORIGINATING, SRV = SSC (Service Code),
SID = 5 for Connection Status Index (CI) of Busy (B) and Normal (N).
STEP 4:ASFC- Assign to the stations a Service Feature Class...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 217
Consecutive Dialing - Attendant C-33
C-33  Consecutive Dialing - Attendant
General Description
This feature gives the ATTENDANT CONSOLE [A-3] the ability to generate DTMF signals while engaged in a
station/trunk connection. These DTMF signals are generated via the dial key pad of the ATTENDANT CONSOLE
[A-3].
Operating Procedure
No manual operation is required.
Service Conditions
1. The ATTENDANT CONSOLE [A-3] can transmit DTMF signals...