NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 198NDA-24297, Issue 1
C-25 Call Forwarding-Intercept / Announcement
Programming (cont’d)
STEP 5:ARRC- If TIE Line or REMOTE ACCESS TO PBX [R-2] connection to the ANNOUNCEMENT
SERVICE Trunk is required, allow trunk-to-trunk connection using ARI-D-RES, Direct Connection.
STEP 6:AAED- Used to assign Announcement equipment. Assign:
TN: Tenant Number
EQP: Announcement Equipment Number
0: Dead Level
1: Unused Number (LCR OPR not programmed)
2: Available
3: Available...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 199
Call Forwarding-Intercept / Announcement C-25
FCCS Programming (cont’d)
1 = Connection is held until the station is released. See the requirements of the application for
the announcement equipment. For Dead level applications, assign data“0”.
R: Sending RBT
0/1 = Yes/No
A: Answer Signal Sending (Answer from the incoming trunk)
0 = No/Yes Normally assign data“1”.
M: Multiple Connection
0/1 = Single Connection/Multiple Connection
LGRT:...

NEAX2400 IPX Feature Programming ManualPage 200NDA-24297, Issue 1
C-26 Call Forwarding - Override
C-26  Call Forwarding - Override
General Description
This feature allows a target user (Station A) to call the station (Station B) which has set CALL FORWARDING -
ALL CALLS [C-5] to it. If the called station (Station B) has set the CALL FORWARDING - BUSY LINE [C-2] to
the calling station (Station A), the calling station (Station A) hears busy tone and can activate CALL BACK [C-1],
EXECUTIVE RIGHT-OF-WAY...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 201
Call Waiting - Answer - DtermC-27D
C-27D  Call Waiting - Answer - Dterm
General Description
This service feature allows a Dtermuser to answer a CAMPED-ON [A-1] or CALL WAITING [C-12, 31] call while
putting an existing call on HOLD [C-6], by pressing the ANSWER key.
Operating Procedure
CAMP-ON [A-1] or CALL WAITING [C-12, 31] to a busy Dterm is activated
1. The user hears Camp-On Indication Tone or Call Waiting Tone during a call in...

NEAX2400 IPX Feature Programming ManualPage 202NDA-24297, Issue 1
C-27D Call Waiting - Answer - Dterm
Programming (cont’d)
System Data 2, Index 10, bit 7. Should the warning tone set in System Data 1, Index 152 be
periodically sent? 0/1: No/Yes. Assign on a per tenant basis.
STEP 2:ASFC- Assign a Service Feature Class that allows SFI’s 5, 6, and 11. This allows the ability to
originate a CALL WAITING - ORIGINATE (SFI 5), to terminate a CALL WAITING -
ORIGINATING [C-31] (SFI 6), and to receive Camp-On...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 203
Call Forwarding - All Calls - Outside C-28
C-28  Call Forwarding - All Calls - Outside
General Description
This feature allows a call, which originates from a station or trunk and is destined for a station, to be routed to another
station outside the NEAX2400 IPX via the appropriate trunk line. This feature can also be activated from a Dterm
multi-line.
Operating Procedure
To set
1. Lift the handset; receive dial tone.
2. Dial the CALL...

NEAX2400 IPX Feature Programming ManualPage 204NDA-24297, Issue 1
C-28 Call Forwarding - All Calls - Outside
Operating Procedure (cont’d)
To cancel from a multi-line Dterm
1. Lift the handset or press the SPEAKER key; receive dial tone. Press the CALL FORWARDING - ALL
CALLS FORWARD feature key; receive service set tone. The LED of the associated feature key will go
out. The LCD displays:
2. Replace the handset or press the SPEAKER key.
Service Conditions
1. CALL FORWARDING - ALL CALLS - OUTSIDE may be...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 205
Call Forwarding - All Calls - Outside C-28
Service Conditions (cont’d)
13. When the incoming call is forwarding to the public network, be sure to add the outgoing access code +
destination area code or the outgoing access code including destination area code number before dialing
subscriber number.
14. A call can be forwarded to a trunk in the remote node via FCCS link.
Interactions
1. A 24-digit limitation exists in memory for CALL...

NEAX2400 IPX Feature Programming ManualPage 206NDA-24297, Issue 1
C-28 Call Forwarding - All Calls - Outside
Programming (cont’d)
System Data 2, Index 6, bit 4. Call-forwarded station restricted from making calls? 0/1: Yes/No.
STEP 2:ANPD- Reserve a number level for feature access and cancel. Assign for Normal (N), Hooking (H),
and Busy (B). Assign NND in accordance with a predetermined numbering plan.
STEP 3:ASPA- Assign an access code to CALL FORWARDING - ALL CALLS [C-5] set SID = 8, and to
CALL...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 207
Call Park C-29
C-29 Call Park
General Description
This feature enables the Attendant(s) or users to“Park”calls against their own extension numbers. Calls can easily
be retrieved from any station within the system.
Operating Procedure
To park a call from the ATTENDANT CONSOLE [A-3]
1. The Attendant presses the CALL PARK key; the CALL PARK number (individual Attendant number) is
automatically selected and displayed at the ATTENDANT CONSOLE...