NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 168NDA-24297, Issue 1
C-11D Call Transfer - All Calls - Dterm
Service Conditions
1. The station performing the CALL TRANSFER - ALL CALLS can disconnect before the called party
answers. If the called station does not answer within the predetermined time, ringing signal is returned to
the transferring station. See VARIABLE TIMING PARAMETERS[V-1]for other selectable timing
choices.
2. In the case of outgoing calls (no answer supervision), this feature may be...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 169
Call Transfer - All Calls - DtermC-11D
Service Conditions (cont’d)
13. The Camp-on by Station is restricted when the target station is in the three-party connection.
14. The Camp-on by Station is not available for the target station in LINE LOCKOUT [L-3] condition.
15. The Camp-on by Station is not available in the following cases:
a.) When the transferred station is dialing the number.
b.) When a call is terminating to the transferred...

NEAX2400 IPX Feature Programming ManualPage 170NDA-24297, Issue 1
C-11D Call Transfer - All Calls - Dterm
Interactions
1. This feature is denied whenever the transferring station is engaged in any state other than a simple two-
party connection.
2. See TRUNK-TO-TRUNK CONNECTION[T-10]for additional programming if the call is to be
transferred off network.
3. If a station is in an established THREE-WAY CALLING [T-2] connection, that station cannot activate
any features. If a station switch hook flashes to...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 171
Call Transfer - All Calls - DtermC-11D
Programming
STEP 1:ASYD- SYS2, Index 0, bit 0=1 (Allow the restriction for Call Back service)
SYS2, Index 5, bit 2. Camp-on by Station is set automatically after the operating station is released
from the connection after encountering the busy target station.
0 = No (Recall to the mediate station)
1 = Yes (Camp On service is set)
SYS2, Index 10, bit 7. Number of time(s) that the warning tone (Call...

NEAX2400 IPX Feature Programming ManualPage 172NDA-24297, Issue 1
C-12 Call Waiting - Terminating
C-12  Call Waiting - Terminating
General Description
This feature enables a busy station to receive a second incoming call. A Camp-On Indication Tone is sent to the busy
station, the user can use a switch hook flash to answer the second call. A switch hook flash may be used to alternate
between the two calls.
Operating Procedure
To activate from a station
1. Dial the desired telephone number.
2. If the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 173
Call Waiting - Terminating C-12
Service Conditions (cont’d)
9. CALL WAITING - TERMINATING cannot be used in conjunction with DIAL ACCESS TO
ATTENDANT [D-2].
10. CALL WAITING - TERMINATING cannot be activated if the target station has accessed, entered, or is
engaged in any of the following features or modes:
ATTENDANT CAMP-ON WITH TONE INDICATION [A-1]
ATTENDANT OVERRIDE [A-7]
BOSS - SECRETARY OVERRIDE - D
term[B-5D]
BUSY VERIFICATION...

NEAX2400 IPX Feature Programming ManualPage 174NDA-24297, Issue 1
C-12 Call Waiting - Terminating
Interactions (cont’d)
5. If ATTENDANT LOOP RELEASE [A-6] is not provided and CALL FORWARDING - DON’T
ANSWER [C-3] via the Attendant Console is provided, a call extended to a station via the Attendant
Console will wait at the station for the time set in Index 141 and will then be forwarded to the destination
station for the time set in Index 145. Index 145 is the total time before recall. When that time...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 175
Call Waiting Lamp C-13
C-13 Call Waiting Lamp
General Description
This feature provides a visual indication to the Attendant when one or more calls are waiting to be answered.
Operating Procedure
Refer to the NEAX2400 IPX Office Data Specification.
Service Conditions
1. All incoming calls to the ATTENDANT CONSOLE [A-3] that have to be answered will signal the
Attendant via the CALL WAITING LAMP.
2. The CALL WAITING LAMP can be set to...

NEAX2400 IPX Feature Programming ManualPage 176NDA-24297, Issue 1
C-13 Call Waiting Lamp
Programming
STEP 1:ASYD- System Data 1, Index 64, Bits 1 & 2. When will the number of calls waiting appear on the
Attendant Console? 00: When Position Available Lamp is on (Attendant Console is not actively
processing a call); 01: When BUSY LAMP FIELD is off; 10: Continuously.
System Data 2, Indexes 8 & 9. These bits flag types of incoming calls to the Attendant Console to be
counted as calls waiting. This is...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 177
CCSA Access C-14
C-14 CCSA Access
General Description
This feature enables connection to a CCSA network. CCSA networks provide customers with the use of a
completely private inter-facility dial system. They use individual facilities for dedicated access lines and trunks that
terminate in common control switching equipment and in various types of telephone equipment at customer
locations.
Operating Procedure
To place an outgoing CCSA call...