NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 128NDA-24297, Issue 1
C-3D Call Forwarding - Don’tAnswer-Dterm
Interactions (cont’d)
4. CALL FORWARDING-DON’T ANSWER-Dtermto an Attendant Console will not operate when the
system is in Night mode. If ATTENDANT NIGHT TRANSFER [A-19] is provided, the call is forwarded
to the ATTENDANT NIGHT TRANSFER [A-19] station.
5. If the CALL FORWARDING-DON’T ANSWER-D
termtarget station is a Dtermand DO NOT DISTURB
[D-21D] has been set, Call Forwarding is not activated. The...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 129
Call Forwarding - Don’tAnswer-DtermC-3D
Programming (cont’d)
STEP 8:ACFO- For tenant-wide CALL FORWARDING-DON’T ANSWER-Dterm, assign CF = 2 for a
destination (CFI) of either the Attendant Console or a station.
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced...

NEAX2400 IPX Feature Programming ManualPage 130NDA-24297, Issue 1
C-5 Call Forwarding - All Calls
C-5  Call Forwarding - All Calls
General Description
This feature permits all calls destined for a particular station to be routed to another station (or to the Attendant)
regardless of the busy or idle status of the called station. Activation and cancellation may be accomplished by either
the individual user or the Attendant.
Operating Procedure
To activate from an individual station
1. Lift the handset;...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 131
Call Forwarding - All Calls C-5
Service Conditions (cont’d)
8. If the stations own telephone number is set for CALL FORWARDING - ALL CALLS, this feature is
changed to CALLING PARTY RECOGNITION SERVICE (CALL FORWARDING - ALL CALLS)
[C-103].
9. When the user setting CALL FORWARDING - ALL CALLS goes off-hook, special dial tone can be
provided instead of dial tone. (Activation of this service is determined by system data.)
10. The OAI monitor...

NEAX2400 IPX Feature Programming ManualPage 132NDA-24297, Issue 1
C-5 Call Forwarding - All Calls
Interactions (cont’d)
7. When CALL FORWARDING-ALL CALLS is in effect, the activating station may be used to originate
calls. See System Data 2, Index 6, Bit 4.
8. When a station is call forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
9. CALL FORWARDING-ALL CALLS can be overridden, allowing Station B to initiate or transfer calls
back to Station A.
10....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 133
Call Forwarding - All Calls - DtermC-5D
C-5D  Call Forwarding - All Calls - Dterm
General Description
This feature permits all calls destined for a particular station to be routed to another station, or to the Attendant,
regardless of the busy or idle status of the called station. Activation and cancellation may be accomplished by the
user or the Attendant. CALL FORWARDING - ALL CALLS - D
termmay be set or cancelled by the user for all...

NEAX2400 IPX Feature Programming ManualPage 134NDA-24297, Issue 1
C-5D Call Forwarding - All Calls - Dterm
Operating Procedure (cont’d)
3. Dial the desired target telephone number; receive service set tone. The LED of the associated feature key
does not light at the station setting the service. If the multi-line appearance is another Dterms MY Line,
that stations feature key LED will light. The setting stations LCD displays:
Target Station
4. Replace the handset or press the SPEAKER key.
5. If the target...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 135
Call Forwarding - All Calls - DtermC-5D
Service Conditions (cont’d)
6. CALL FORWARDING - ALL CALLS - Dtermmay also be accessed via the dial pad or SPEED
CALLING-ONE TOUCH [S-26D]. If this feature is accessed via the dial pad, it must also be cancelled
via the dial pad.
7. A user may set CALL FORWARDING - ALL CALLS - D
termfor a multi-line appearance based on the
CLASS OF SERVICE - INDIVIDUAL [C-15] assigned to the station setting the...

NEAX2400 IPX Feature Programming ManualPage 136NDA-24297, Issue 1
C-5D Call Forwarding - All Calls - Dterm
Service Conditions (cont’d)
15. A call can be forwarded to an Attendant Console in the remote node via FCCS link.
16. When a call is forwarded through FCCS link, the numbering plans of the originally called station and the
forwarded Attendant Console must be the same.
Interactions
1. Users are unaccustomed to hearing ringback tone when responding to their own station’s ring. Inform
users when...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 137
Call Forwarding - All Calls - DtermC-5D
Programming (cont’d)
System Data 1, Index 69, Bit 1 (Bit 2 - Burst of Tone for Recall). A burst of ringback tone to alert the
person receiving a CALL FORWARDING - ALL CALLS - Dtermcall. In service? 0/1: No/Yes.
Normally assigned as data“0”.
System Data 2, Index 6, Bit 4. Enables station set for CALL FORWARDING-ALL CALLS-D
termto
be allowed to use phones normally. If data“0”is assigned, the station...