NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 178NDA-24297, Issue 1
C-15 Class Of Service - Individual
C-15  Class Of Service - Individual
General Description
This feature permits all NEAX2400 IPX stations to be assigned a Class of Service in accordance with the degree of
system use desired. Each station is assigned one class from each of three groups.
Operating Procedure
CLASS OF SERVICE - INDIVIDUAL is assigned via system data entry. Thereafter, each station is automatically
provided with the desired...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 179
Class Of Service - Individual C-15
Interactions (cont’d)
2. CALL FORWARDING [C-2, 3, 5]: Station-to-station calls can be forwarded to a fully restricted station.
An attempt to forward an incoming trunk call to a fully restricted station will result in reorder tone.
3. STATION HUNTING [S-7, 8, 9]: Any call directed to a busy, fully restricted station will hunt to an
alternate station. Careful consideration is required when assigning a...

NEAX2400 IPX Feature Programming ManualPage 180NDA-24297, Issue 1
C-15 Class Of Service - Individual
Programming (cont’d)
TEC: Telephone Class (1-31)
1: DP (10pps)
2: PB
3: DP/PB
12: D
term
13: Data terminal via Dterm
14: Hotline
15: CAS Line
16: Data terminal via Data Module
18: Virtual Circuit
23: ISDN Terminal
27: Eight Conference Equipment
RSC: Route Restriction Class (0-15). For assignment of RSC, ARSC command.
SFC: Service Feature Class (0-15). For assignment of SFC, ASFC command.
STEP 3:ASCL- This...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 181
Consultation Hold - All Calls C-17
C-17  Consultation Hold - All Calls
General Description
This feature permits a user to hold any incoming or outgoing public network or TIE Line call, or any intra-office
call, while originating a call to another station within the system.
Operating Procedure
Holding the original call and placing the second call
1. Press the switch hook; receive special dial tone.
2. The original call is held.
3. Dial the...

NEAX2400 IPX Feature Programming ManualPage 182NDA-24297, Issue 1
C-17 Consultation Hold - All Calls
Interactions (cont’d)
5. Features that cannot be activated while a user has a party in CONSULTATION HOLD-ALL CALLS are:
EXECUTIVE RIGHT-OF-WAY [E-1]
TRUNK ANSWER FROM ANY STATION [T-8]
CALL BACK, Activate or Cancel [C-1]
CALL PICKUP-DIRECT [C-30]
CALL FORWARDING, Activate or Cancel [C-2, 3, 5]
OUTGOING TRUNK QUEUING, Cancel [O-2]
SPEED CALLING-INDIVIDUAL, Entry [S-21]
MESSAGE REMINDER [M-19D]
6. All other...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 183
Consultation Hold - All Calls C-17
Programming (cont’d)
System Data 1, Index 157. Trunk Soft Hold Timer A, used with senderized trunks. Assign data 00H for
a value of 18 seconds. (Data 31H may be used for a value of two seconds, if CALL TRANSFER-ALL
CALLS [C-11] is to be used immediately after connecting to the trunk.). This is the time between trunk
connection and when switch hook flash is allowed on a senderized trunk connection. It is...

NEAX2400 IPX Feature Programming ManualPage 184NDA-24297, Issue 1
C-17D Consultation Hold - All Calls - Dterm
C-17D  Consultation Hold - All Calls - Dterm
General Description
ThisfeaturepermitsaDtermuser to hold any incoming or outgoing public network or TIE Line, or any Intra-office
calls, while originating a call to another station within the system.
Operating Procedure
To hold original call and place second call from a Dterm
1. Press the TRANSFER key; receive special dial tone.
2. The original call is...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 185
Consultation Hold - All Calls - DtermC-17D
Interactions (cont’d)
5. Features that cannot be activated while a user has a party in CONSULTATION HOLD-ALL CALLS are:
EXECUTIVE RIGHT-OF-WAY [E-1]
TRUNK ANSWER FROM ANY STATION [T-8]
CALL BACK, Activate or Cancel [C-1]
CALL PICKUP-DIRECT [C-30]
CALL FORWARDING, Activate or Cancel [C-2, 3, 5]
OUTGOING TRUNK QUEUING, Cancel [O-2]
SPEED CALLING-INDIVIDUAL, Entry [S-21]
MESSAGE REMINDER [M-19D]
6....

NEAX2400 IPX Feature Programming ManualPage 186NDA-24297, Issue 1
C-17D Consultation Hold - All Calls - Dterm
Programming (cont’d)
System Data 1, Index 157. Trunk Soft Hold Timer A, used with senderized trunks. Assign data 00H for
a value of 18 seconds. (Data 31H may be used for a value of two seconds, if CALL TRANSFER-ALL
CALLS [C-11] is to be used immediately after connecting to the trunk.). This is the time between trunk
connection and when switch hook flash is allowed on a senderized trunk...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 187
Centralized Attendant Service (CAS) C-20
C-20  Centralized Attendant Service (CAS)
General Description
For applications requiring multiple sites, but having common interests or operation, the NEAX2400 IPX can operate
in a Main (attended) or Satellite (unattended) configuration. Typically, incoming calls to the satellite are routed to
the main location for processing by the Central Attendant(s) within the CAS network. This service feature...