NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 228NDA-24297, Issue 1
C-69 Call Forwarding - All Calls - Announcement
Programming (cont’d)
STEP 4:AT R K- Assign the LENs. Announcement Trunk Route Number, Trunk Number, and Tenant Number.
Assign one or more trunks to a specific route used to connect to an announcement machine.
STEP 5:MBTK- Assign the Make Idle status to the announcement trunk.
STEP 6:ADSL- Assign SN=1 (Originating; DT Connection) and FKY=2 (Call Forwarding - All Calls; FDA).
This command is...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 229
Call Back - Delayed C-73
C-73  Call Back - Delayed
General Description
This feature allows a station to which CALL BACK [C-1] has been set to initiate another call, within a
predetermined time period after becoming idle and before the CALL BACK [C-1] feature is activated.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is assigned in system programming, on a system-wide basis.
2. The CALL...

NEAX2400 IPX Feature Programming ManualPage 230NDA-24297, Issue 1
C-74 Call Forwarding - Don’tAnswer-Outside
C-74  Call Forwarding - Don’t Answer - Outside
General Description
This feature allows a call which originates from a station or trunk, and is destined for a station, to be routed to another
station outside the NEAX2400 IPX via the appropriate trunk line. This service feature can also be activated from a
D
termmulti-line.
Operating Procedure
To set
1. Lift the handset; receive dial tone.
2. Dial...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 231
Call Forwarding - Don’tAnswer-Outside C-74
Operating Procedure (cont’d)
Note:*A dialed abbreviated number is translated into the forwarding number and the first eight digits are
displayed even if 24 digits can be stored.
To cancel from a multi-line Dterm
1. Press the multi-line key for the station CALL FORWARDING - DONT ANSWER-OUTSIDE is to be
cancelled.
2. Lift the handset or press the SPEAKER key; receive dial tone.
3. Press the CALL...

NEAX2400 IPX Feature Programming ManualPage 232NDA-24297, Issue 1
C-74 Call Forwarding - Don’tAnswer-Outside
Service Conditions (cont’d)
b.) When originating a call from a trunk: Restriction for tandem connections between the incoming
trunk and the outgoing trunk selected for the call where this feature occurs.
10. There is no limit to the number of stations that may activate this feature simultaneously.
11. When the called station does not answer for a predetermined time interval, this feature is...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 233
Call Forwarding - Intercept / Announcement - Attendant C-75
C-75  Call Forwarding - Intercept / Announcement - 
Attendant
General Description
This feature provides for interception of Attendant-originated calls that cannot be completed (unassigned station,
level, etc.). These calls are automatically routed to a recorded announcement informing the caller that an inoperative
number was reached.
Operating Procedure
No manual operation is...

NEAX2400 IPX Feature Programming ManualPage 234NDA-24297, Issue 1
C-75 Call Forwarding - Intercept / Announcement - Attendant
Programming
Programming of hardware into system data is required. Refer to CALL FORWARDING-
INTERCEPT/ANNOUNCEMENT[C-25]. Timers are also programmed into system data (see
VARIABLE TIMING PARAMETER[V-1]).
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 235
Call Waiting Lamp - UCD C-76
C-76  Call Waiting Lamp - UCD
General Description
This feature uses an LED indication, which is one of the programmable keys on the Dterm, to indicate when a call is
waiting to be answered in the UCD queue.
Operating Procedure
No manual operation is required.
Service Conditions
1. The UCD Call Waiting Lamp displays the status of the UCD group as follows:
Lamp On: One or more calls waiting in the UCD queue....

NEAX2400 IPX Feature Programming ManualPage 236NDA-24297, Issue 1
C-76 Call Waiting Lamp - UCD
Interactions (cont’d)
6. If OVERFLOW-UCD [O-13] is programmed, overflow to the second group will take place if all stations
in the first group are either busy or in the busy-out state. There will be no CALL WAITING LAMP-UCD
indication to the first group.
7. If the overflow group is all busy, queuing takes place to the first group and the CALL WAITING LAMP-
UCD will light to indicate a queuing condition at the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 237
Call Waiting Lamp - UCD C-76
FCCS Programming (cont’d)
CWT: Call Waiting Threshold Value (1-255)
MCI: 0/1=Message Center Interface data transfer is Valid/Invalid.
Note 1:When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN.
Note 2:When programming the data, initialize the ELC card which accommodates the UCD group station.