NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 188NDA-24297, Issue 1
C-20 Centralized Attendant Service (CAS)
Operating Procedure (cont’d)
Remote Hold
1. The Attendant converses with a central office party.
2. The Attendant presses the SHF key; hears special dial tone.
3. The Attendant dials the Remote Hold access code (one or two digits); the central office party is placed in
the hold state at the satellite system, and the Attendant hears the hold confirmation tone (five, 50 msec.
bursts of 440 Hz).
4. The...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 189
Centralized Attendant Service (CAS) C-20
Service Conditions (cont’d)
2. RLTs can be seized in one direction only; from the satellite PBX to the main PBX.
3. The Attendant cannot originate or INTER-POSITION TRANSFER [I-5] a call on an RLT.
4. The Attendant cannot extend an incoming CAS call to a station, trunk, or another Attendant in the main
system.
5. CALL PROCESSING INDICATION [C-8] is not provided to the Attendant serving the incoming...

NEAX2400 IPX Feature Programming ManualPage 190NDA-24297, Issue 1
C-20 Centralized Attendant Service (CAS)
Interactions (cont’d)
9. When the Night stations are located at the satellite PBX and no Attendant Console is provided, a Night
key must be installed at the satellite location to activate night service. When the key is operated, the CAS
operations are suspended, and incoming calls are terminated at the NIGHT CONNECTION FIXED/
FLEXIBLE station(s) [F-1, 2] or via TRUNK ANSWER FROM ANY STATION [T-8]....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 191
Centralized Attendant Service (CAS) C-20
Programming (cont’d)
STEP 4:ACS I- Assign the Incoming CAS Route and Trunk to the Night Station and Tenant number. Assign
the CSI = 4 for Night Connection.
TAS
STEP 1:ANPD- Reserve a number level for feature access.
STEP 2:ASPA- Assign an access code to TRUNK ANSWER ANY STATION, SRV = SSC (Service Code);
SID = 16. Assign for a Connection Status Index (CI) of Normal (N).
STEP 3:ACFR- Assignment of...

NEAX2400 IPX Feature Programming ManualPage 192NDA-24297, Issue 1
C-20 Centralized Attendant Service (CAS)
Programming (cont’d)
STEP 7:ACS I- Assign the Incoming Satellite trunks to be answered at the Main system CSI = 3, Direct In
Termination, Day and Night Mode. Then assign the stations programmed above. This ties incoming
trunks to the PA-4ODTs.
STEP 8:ACFR- Assignment of Call Forwarding Restriction. Upon determining which types of Call Class
Indexes (CCI) will be answered at the Main system, such as...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 193
Code Calling Access C-21
C-21  Code Calling Access
General Description
This feature provides the ATTENDANT CONSOLE [A-3] and users dial access to Code Calling equipment.
Operating Procedure
1. Go off hook; receive dial tone.
2. Dial the CODE CALLING ACCESS code.
3. Dial the code number for the unit desired.
Service Conditions
1. Amplifiers, speakers, and Code Calling units must be provided by the customer.
2. Loop Start Central Office...

NEAX2400 IPX Feature Programming ManualPage 194NDA-24297, Issue 1
C-22D Called Station Status Display - Dterm
C-22D  Called Station Status Display - Dterm
General Description
This feature provides for the status of a called station to appear on the LCD display of a calling Dterm.
Operating Procedure
Lift handset or press SPEAKER key; dial desired station. The LCD display indicates the status of the called station.
Service Conditions
1. If the called station is idle, the display flashes its number until...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 195
Calling Number Display - DtermC-24D
C-24D  Calling Number Display - Dterm
General Description
This feature provides for the station and trunk number of an incoming call to appear on the Dterms LCD display.
This display will flash while the call is ringing, then appear steady when the call is answered.
Operating Procedure
No manual operation is required.
Service Conditions
1. When a call terminates on a line other than the PRIME LINE...

NEAX2400 IPX Feature Programming ManualPage 196NDA-24297, Issue 1
C-25 Call Forwarding-Intercept / Announcement
C-25  Call Forwarding-Intercept / Announcement
General Description
This feature provides for interception of STATION-TO-STATION [S-11], DIRECT INWARD DIALING [D-8],
Attendant-to-Station and CCSA [C-14] calls that cannot be completed (unassigned station, level, etc.). These calls
are automatically routed to a recorded announcement informing the caller that an inoperative number was reached
and...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 197
Call Forwarding-Intercept / Announcement C-25
Service Conditions (cont’d)
When encountering all trunks busy
14. This service feature is valid for outgoing station-to-trunk or tandem trunk-to-trunk connections.
15. Automatic OUTGOING TRUNK QUEUING [O-2], OFF-HOOK QUEUING [O-7] and ROUTE
ADVANCE [R-6] are mutually exclusive with this feature. These features take priority over OUTGOING
TRUNK BUSY - ANNOUNCEMENT [O-21].
16. ANNOUNCEMENT...