NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 218NDA-24297, Issue 1
C-33 Consecutive Dialing - Attendant
Programming
ASYD- System Data 1, Index 229, Bit 2. DTMF signal sending with the keypad pressed after the
attendant has answered an incoming call 0/1: Out/In Service.
System Data 3, Index 11. Assign a Miscellaneous Timer counter for the duration of the DTMF Sender
Tone. 128ms X (PBST + 1) = Duration of Sender Tone. Maximum value is 2.048 seconds.
765 4 3 2 1 0
PBST 

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 219
Called Number Display - Attendant C-59
C-59  Called Number Display - Attendant
General Description
If a call is transferred to the ATTENDANT CONSOLE [A-3] as a result of:
DO NOT DISTURB [D-11]
CALL FORWARDING - ALL CALLS [C-5]
CALL FORWARDING - BUSY LINE [C-2]
CALL FORWARDING - DONT ANSWER [C-3]
CALL FORWARDING - INTERCEPT/ ANNOUNCEMENT [C-25]
Information pertaining to the called station is displayed on the Attendant Console.
Operating...

NEAX2400 IPX Feature Programming ManualPage 220NDA-24297, Issue 1
C-60 Call Forwarding - Busy Line - Outside
C-60  Call Forwarding - Busy Line - Outside
General Description
This feature allows a call that originates from a station or trunk, and is destined for a station to be routed to another
station outside the NEAX2400 IPX via the appropriate trunk line. This service feature can also be activated from a
D
termmulti-line.
Operating Procedure
To set
1. Lift the handset; receive dial tone.
2. Dial the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 221
Call Forwarding - Busy Line - Outside C-60
Operating Procedure (cont’d)
To cancel from a multi-line Dterm
1. Press the multi-line key of the station to which CALL FORWARDING - BUSY LINE-OUTSIDE is to be
cancelled.
2. Lift the handset or press the SPEAKER key; receive dial tone.
3. Press the CALL FORWARDING - BUSY LINE - OUTSIDE feature key; receive service set tone. The
LED of the associated feature key will go out. The LCD displays:
4....

NEAX2400 IPX Feature Programming ManualPage 222NDA-24297, Issue 1
C-60 Call Forwarding - Busy Line - Outside
Service Conditions (cont’d)
b.) When originating a call from a trunk Restriction for Tandem connections between the incoming
trunk and the outgoing trunk selected for the call where CALL FORWARDING - BUSY LINE
service occurs.
12. When a caller places a call via OGCA (Outgoing Call Alternative) and when the first outgoing route and
the calling party are restricted, this service cannot be set. In...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 223
Call Forwarding - Busy Line - Outside C-60
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
 Note 1
STEP 1:ANPDL- Reserve a number level for feature access and cancel. Assign...

NEAX2400 IPX Feature Programming ManualPage 224NDA-24297, Issue 1
C-62 Consecutive Speed Calling - System
C-62  Consecutive Speed Calling - System
General Description
This feature allows a user to call frequently dialed DID numbers using fewer digits (abbreviated call codes) than
would normally be required. The stored digits would include route access code, area code and office code. The caller
would then manually enter the called telephone number.
Operating Procedure
1. Dial the Speed Calling access...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 225
Consecutive Speed Calling - System C-62
Programming (cont’d)
STEP 3:ASPA- Assign an access code to SPEED CALLING-SYSTEM, assign SRV = SSC (Service Code),
SID = 15. Program for Normal (N). NND = Access code plus Abbreviated Digit Code (ADC). See
ASPD. For example:
6 + 010
1 digit + 3 digits = NND = 4
STEP 4:ASFC- Assign a Service Feature Class that allows SFI 12 to stations that will have SPEED
CALLING-SYSTEM.
STEP 5:ASPD- Assign the...

NEAX2400 IPX Feature Programming ManualPage 226NDA-24297, Issue 1
C-69 Call Forwarding - All Calls - Announcement
C-69  Call Forwarding - All Calls - Announcement
General Description
This feature permits all calls destined for a particular station to be routed to a recorded announcement. Activation
and cancellation may be accomplished by either the individual user or the ATTENDANT CONSOLE [A-3].
Operating Procedure
To activate from an individual station
1. Lift the handset; receive dial tone.
2. Dial the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 227
Call Forwarding - All Calls - Announcement C-69
Service Conditions (cont’d)
10. This service feature is available with the following connections:
DIRECT INWARD DIALING (DID [D-8]
DIRECT-IN TERMINATION (DIT) [D-7]
STATION-TO-STATION CALLING [S-11]
Station calls from a TIE Line Trunk
11. When a designation of CALL FORWARDING - ALL CALLS - ANNOUNCEMENT has already been
assigned, even if the feature is restricted by the new office data or...