NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 238NDA-24297, Issue 1
C-81 Call Forwarding - I’mHere
C-81  Call Forwarding - I’m Here
General Description
This service feature permits the CALL FORWARDING - ALL CALLS feature to be set/cancelled from the target
station.
Operating Procedure
To set from the target station
1. Go off-hook; receive dial tone.
2. Dial the CALL FORWARDING - IM HERE access code (from the target station); receive special dial
tone.
3. Dial the forwarding telephone number; receive...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 239
Call Forwarding - I’mHere C-81
Service Conditions (cont’d)
12. When using the FCCS network, if the destination (target station) is a Dterm, CALL FORWARDING - I’M
HERE can be set or cancelled from a sub line of a Dterm. At that time, the transferred call terminates to the
My Line of the Dtermthat sets the service.
13. When using the FCCS network, the service can be set or cancelled when the forwarding station is idle.
14. When using the...

NEAX2400 IPX Feature Programming ManualPage 240NDA-24297, Issue 1
C-81 Call Forwarding - I’mHere
FCCS Programming (cont’d)
SYS1, Index 5, b1~3. Maximum number of Multiple Call Forwarding - All Calls/Busy Line
occurrences:
Note:This data is valid when SYS-1, Index 69, bit 7 is assigned as“1”.
SYS 1, Index 69, b1. Send short tone when a call forwarded via Call Forwarding - All Calls service is
answered.
0/1 = Not Required/Required
SYS 1, Index 69, b7. Multiple Call Forwarding - Busy Line/All Calls
0/1 =...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 241
Centrex Compatibility C-109
C-109 Centrex Compatibility
General Description
This feature allows a DTMF type telephone user engaged in a trunk call to send a hooking signal to the called office,
enabling the call to be transferred to another station in that office.
Operating Procedure
Station A is connected to Station B, accommodated in another office
1. Station A presses switch hook; receives special dial tone of the called office. Dial...

NEAX2400 IPX Feature Programming ManualPage 242NDA-24297, Issue 1
C-133 Call Forwarding - Don’t Answer To UCD Queue
C-133 Call Forwarding - Don’t Answer To UCD Queue
General Description
This feature allows calls to a station that has set CALL FORWARDING-DONT ANSWER to a UNIFORM CALL
DISTRIBUTION group to be added to a UCD queue if all stations in the UCD group are busy. (Originally, calls
forwarded to a UCD group would receive reorder tone if all stations in the group were busy.)
Operating Procedure
The...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 243
Call Hold - Conference C-146
C-146  Call Hold - Conference
General Description
This feature allows a user to establish a conference connection by adding a third party who is held on a multiline of
aDtermto the existing two-party connection. The held call which is to be added may be a station or trunk call.
Operating Procedure
To operate from a Dterm
1. Make a trunk/station call using line A on the Dterm.
2. Place the in-progress call on...

NEAX2400 IPX Feature Programming ManualPage 244NDA-24297, Issue 1
C-146 Call Hold - Conference
Service Conditions (cont’d)
6. This service is available when the parties (A), (C), the lines (A) and (B) are the following:
a.) interoffice trunk (including ISDN line)
b.) C.O. line/tie line
c.) station, including virtual stations.
In case the ISDN terminal, intercom line, hot line, or CAS line is used, the service is restricted.
7. Data communications are not considered in this service.
8. A D
termuser dials...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 245
Call Block C-150
C-150 Call Block
General Description
This feature is a part of Caller ID service. This feature restricts termination of incoming calls from the preassigned
calling numbers. This feature is available by designating the calling number by the MAT.
Call Block is used to restrict an incoming call that has a Restriction Number (Physical Station Number, telephone
number or the Caller ID number, which are preset by each station)....

NEAX2400 IPX Feature Programming ManualPage 246NDA-24297, Issue 1
C-150 Call Block
Operating Procedure (cont’d)
To set the Restriction Number by dialing an optional number
1. Lift the handset.
2. Press the CALL BLOCK key.
3. Receive special dial tone.
4. Dial number to be restricted.
5. Receive service set tone after the preassigned inter-digit timer (default is 6 seconds).
Note 1
6. The CALL BLOCK key lights red.
7. The dialed number is registered as the Restriction Number.
To confirm the registered...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 247
Call Block C-150
Operating Procedure (cont’d)
When confirming the Restriction Number:
When HELP Key for CALL BLOCK of Soft key is pressed:
Service Conditions
When the Restriction Number is registered by the MAT
1. When the calling number is not received, this service is not activated.
2. The calling number for this service is assigned to the parameter CID of ACID command. When only the
first part of the calling number is assigned to the...