NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 278NDA-24297, Issue 1
D-7 Direct-In Termination (DIT)
Service Conditions (cont’d)
17. When activating this feature via the FCCS network, when the telephone number of the destination station
is deleted:
a.) When the Attendant Console is used, the DIT call terminates to the Attendant Console.
b.) When the Attendant Console is not used, or if the Attendant Console is in night mode, the caller
hears ringback tone.
18. When activating this feature via the FCCS...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 279
Direct-In Termination (DIT) D-7
Programming (cont’d)
STEP 5:ARSC- The DIT target station receiving the call must be assigned a Route Restriction Class (RSC),
allowing the station to be connected to the trunk. The DIT route must be allowed via Route Restriction
Indexes (RRI) 0 & 1.
STEP 6:ACFR- Designate the type of incoming Call Class Indexes (CCI) that require a Transfer Service
Feature Index (TSFI) = 3, DIRECT-IN TERMINATION. The type...

NEAX2400 IPX Feature Programming ManualPage 280NDA-24297, Issue 1
D-8 Direct Inward Dialing (DID)
D-8  Direct Inward Dialing (DID)
General Description
This feature provides for all incoming calls from the public network (except FX or WATS) to reach any system
station without Attendant assistance.
Operating Procedure
The calling party, outside the system, dials the telephone number as usual. However, the call is answered directly at
a predetermined station, bypassing the Attendant.
Service Conditions
1....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 281
Direct Inward Dialing (DID) D-8
Programming
STEP 1:ASYD- System Data 1, Index 16, Bit 3. Enable the 4-digit station number. It is normal to enable all
options regarding length of station numbering. Assign data 1FH.
System Data 1, Index 65. Assign the number of routes in the system.
System Data 1, Index 70, Bit 0. Is Calling Number for a DID incoming to the Attendant in service? 0/
1: No/Yes.
STEP 2:ARTD- Assign the DIRECT INWARD DIALING...

NEAX2400 IPX Feature Programming ManualPage 282NDA-24297, Issue 1
D-9 Direct Outward Dialing (DOD)
D-9  Direct Outward Dialing (DOD)
General Description
This feature permits any user to gain access to the public network without the assistance of the Attendant, by dialing
an access code and receiving a second dial tone. The user may then proceed to dial the desired public network
number.
Operating Procedure
To place an outside call
1. Go off-hook; receive dial tone,
2. Dial the trunk access code...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 283
Direct Outward Dialing (DOD) D-9
Programming
STEP 1:ASYD- System Data 1, Index 65. Assign the number of routes in the system.
STEP 2:ANPD- Reserve a number level for outgoing trunk access. Assign for Normal (N) and Hooking (H).
Assign NND in accordance with a predetermined numbering scheme.
STEP 3:ASPA- Assign the access code as assigned in ANPD above. Type of Service, SRV = OGC (Outgoing
Call) Outgoing Trunk. Assign the route number...

NEAX2400 IPX Feature Programming ManualPage 284NDA-24297, Issue 1
D-10 Distinctive Ringing
D-10 Distinctive Ringing
General Description
This feature provides distinctive station ringing patterns so that the user can distinguish between internal and
external incoming calls.
Operating Procedure
No manual operation is required.
Service Conditions
Ringing Patterns
1. Ringing for Incoming Internal Call
a.) When a Service Feature Class that allows Personal Ringer (ASFC command, SFI 148) is assigned
to a...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 285
Distinctive Ringing D-10
Interactions (cont’d)
2. CONSULTATION HOLD [C-17]: Station A places Party B on CONSULTATION HOLD [C-17] and
calls Station C. If Party B is a trunk, Station C hears DISTINCTIVE RINGING for a trunk call. If Party
B is a station, Station C hears distinctive ringing for a station call.
3. When Personal Ringer function is set to a station, if an incoming internal call is terminated to the personal
number and the call...

NEAX2400 IPX Feature Programming ManualPage 286NDA-24297, Issue 1
D-11D Do Not Disturb - Dterm
D-11D  Do Not Disturb - Dterm
General Description
This feature allows a user to establish DO NOT DISTURB status. Incoming calls will be denied access to MY Line,
while DO NOT DISTURB status is in effect.
Operating Procedure
To set
1. Press the DO NOT DISTURB (DND) key. The associated LED will light. The LCD displays:
To cancel
2. Press the DO NOT DISTURB (DND) key. The LED will go out. The LCD displays:
Service...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 287
Do Not Disturb - DtermD-11D
Interactions
1. DO NOT DISTURB may be listed in some literature as available by a programmable Line/Feature key. A
DtermACD station is not equipped with a DND key. If DO NOT DISTURB is to be made available to this
station, it must be programmed to a Line/Feature key.
2. DATA INTERFACE-AUTOMATIC ANSWER may be activated if the D
termstation is in the DO NOT
DISTURB mode.
Programming
STEP 1:AKYD- Assign the...