NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 68NDA-24297, Issue 1
A-121 Add On Conference - 8 Party
A-121  Add On Conference - 8 Party
General Description
This service allows the 8-party conference to be established any time by any conferee by use of the 8-party
conference trunk.
Operating Procedure
To establish an 8-party conference
1. Station A calls Station B; Station B answers.
2. Station A (or B) switch hook flashes (or press TRANSFER key) and dials Station C’s number; Station C
answers.
3. Station A...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 69
Add On Conference - 8 Party A-121
Service Conditions (cont’d)
9. When all of the eight ports of the 8-party conference trunk are filled with the conferees, no other conferee
can be added to the conference.
10. The station/trunk which is connected to the 8-party conference trunk can release from the conference at
any time.
11. An incoming call from the ringdown trunk, where release cannot be detected, cannot be connected to the
8-party...

NEAX2400 IPX Feature Programming ManualPage 70NDA-24297, Issue 1
A-121 Add On Conference - 8 Party
Service Conditions (cont’d)
24. The station setting Retain Conference can only cancel Retaining Conference or go on-hook. (No other
operation is available.) When the station goes on-hook, the RETAIN CONF lamp turns off.
25. In case of trunk call origination, the billing is performed against the station which originated the trunk call
until the trunk releases. Therefore, there may be several billing messages...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 71
Add On Conference - 8 Party A-121
Programming (cont’d)
STEP 5:ASHP- When the system accommodates multiple PA-CFTB circuit cards, assign a STATION
HUNTING - TERMINATING group for the stations programmed to LEN level 0 of each PA-CFTB
circuit card. For more details, see the figure below:
STEP 6:AKYD-assignFKY83toanyD
terms that require the use of the Retain Conference feature.
STEP 7:ADSL- Assign SN=3 (STATION BUSY) and FKY=13 (THREE-WAY...

NEAX2400 IPX Feature Programming ManualPage 72NDA-24297, Issue 1
A-125 Analog Caller ID (Class SM)
A-125  Analog Caller ID (Class SM)
General Description
This feature allows the Dtermto display calling party’s number and/or name on the LCD when a call from analog
C.O. line is terminated. In addition, the calling number can be output as a part of SMDR information.
Caller ID information can be displayed on an analog telephone with a display device or the display of a D
term.
Operating Procedure
No manual...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 73
Analog Caller ID (Class SM) A-125
Service Conditions (cont’d)
d.) The display is flashing during termination. It is lit during conversation.
e.) The following are examples of displays when the received digits of a calling number and name
exceed the display field:
OR
OR
OR
Programming
See also TRUNK LINE APPEARANCE[T-23]for information on how to accommodate C.O. line on
aDtermline/feature key.
STEP 1:ASYD- System Data 1, Index 241, Bit 6....

NEAX2400 IPX Feature Programming ManualPage 74NDA-24297, Issue 1
A-125 Analog Caller ID (Class SM)
Programming (cont’d)
System Data 1, Index 288, Bit 5. Expanded SMDR Output for SMDR A Apparatus. 0/1=Out/In
Service.
System Data 1, Index 290, Bit 5. Expanded SMDR Output for SMDR B Apparatus. 0/1=Out/In
Service.
System Data 1, Index 292, Bit 5. Expanded SMDR Output for SMDR C Apparatus. 0/1=Out/In
Service.
System Data 1, Index 294, Bit 5. Expanded SMDR Output for SMDR D Apparatus. 0/1=Out/In
Service....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 75
Analog Caller ID - Station A-127
A-127  Analog Caller ID - Station
General Description
This feature allows a called station to receive CALLER ID information (time, calling number and name) from
Central Office when a call terminates via the analog COT. The calling number received from the ISDN network,
MF-ANI information received from Central Office with the MF feature or the calling telephone number within the
PBX can change into CALLER ID...

NEAX2400 IPX Feature Programming ManualPage 76NDA-24297, Issue 1
A-127 Analog Caller ID - Station
Service Conditions (cont’d)
b.) Message types of Caller ID information sent to a called analog station are as follows:
Message type - 04H: Calling Number Delivery Information (for calling number)
Message type - 80H: Call Setup (for calling number, name, or reason not to inform)
Parameter - 02H: Calling line DN parameter
- 04H: Reason for absence of calling DN Parameter
- 07H: Name
- 08H: Reason for...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 77
Analog Caller ID - Station A-127
Service Conditions (cont’d)
q.) When the calling party or the intermediate party is Attendant Console, or the calling party number
is not received when the call is terminated via C.O. line or tie line, the calling number cannot be
notified.
r.) When the Name Display data is assigned to the calling party in station-to-station calling, the
calling party’s name is also sent to the called party. Note that only...