NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 18NDA-24297, Issue 1
A-15 Announcement Service
A-15 Announcement Service
General Description
This feature allows a user to hear a prearranged announcement when the user dials a predetermined access code.
Operating Procedure
1. Lift the handset; receive dial tone.
2. Dial the announcement trunk access code.
3. Listen to the message from the announcement machine.
Service Conditions
1. This feature requires one of the following hardware alternatives:
a.) Central...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 19
Announcement Service A-15
Programming (cont’d)
STEP 3:ARTD- Assign the announcement route as shown below. Be sure to provide privacy by programming
CDN 44:PRV as data“1”.
RT: 1
1-OSGS :2 2-ONSG :3 5-TF :1 6-TCL :1 7-L/T :1
8-RLP :2 15-LSG :4
STEP 4:ARSC- Assign a Route Restriction Class (RSC) to the station that allows access to the Announcement
route. Assign RSC 0 to the Attendant, and allow that RSC access to the Announcement route.
STEP...

NEAX2400 IPX Feature Programming ManualPage 20NDA-24297, Issue 1
A-15 Announcement Service
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
STEP 1:ALRTN- This data must be assigned to the NCN.
Assign the logical route number to the physical...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 21
Alternate Routing A-16
A-16 Alternate Routing
General Description
This feature automatically routes outgoing on or off-net calls over alternate facilities when the first-choice trunk
group is busy. The user selects the first-choice route by dialing the corresponding access code, and the equipment
then routes the call through alternate trunk groups only if the first is busy. The NEAX2400 IPX will also add or
delete digits, when necessary,...

NEAX2400 IPX Feature Programming ManualPage 22NDA-24297, Issue 1
A-16 Alternate Routing
FCCS Programming 
Refer to the NEAX2400 IPX Fusion Network System Manual. 

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 23
Audible Indication Control A-17
A-17 Audible Indication Control
General Description
This feature allows the Attendant to adjust the audible indications provided to the ATTENDANT CONSOLE [A-3].
Operating Procedure
The Attendant Console is equipped with a volume control that can raise or lower the internal speaker level. The
volume control is located on the left side of the Attendant Console. The audible indication may also be turned off...

NEAX2400 IPX Feature Programming ManualPage 24NDA-24297, Issue 1
A-18 Account Code
A-18 Account Code
General Description
This feature is an adjunct to STATION MESSAGE DETAIL RECORDING [S-10], which provides a user with the
capability to enter a cost-accounting or client-billing code (up to 10 digits) into the system before dialing a long
distance number.
Operating Procedure
To enter an ACCOUNT CODE
1. Lift the handset; receive dial tone.
2. Dial the feature access code; receive service set tone.
3. Dial...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 25
Account Code A-18
Interactions (cont’d)
5. The access code for ACCOUNT CODES is restricted to a maximum of three digits.
6. STATION MESSAGE DETAIL RECORDING [S-10] Split Billing (System Data Option): On transferred
calls, or incoming calls via the Attendant Console, the ACCOUNT CODE will be recorded in all the call
records.
7. When OUTGOING TRUNK QUEUING [O-2] is initiated, the ACCOUNT CODE will be recorded when
the call is completed.
8....

NEAX2400 IPX Feature Programming ManualPage 26NDA-24297, Issue 1
A-18 Account Code
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note
STEP 1:ANPDL- Reserve a number level for service feature access. Assign Connection Index, CI = N, H, B;...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 27
Attendant Night Transfer A-19
A-19  Attendant Night Transfer
General Description
When the ATTENDANT CONSOLE [A-3] is in night mode, any operator calls (dial 0 calls) are automatically
routed to a predetermined night station.
Operating Procedure
To answer night call
1. The user dials the operator call code; receives ringback tone.
2. An operator call is automatically transferred to the night answer station.
3. The calling party hears...