NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 28NDA-24297, Issue 1
A-19 Attendant Night Transfer
Service Conditions (cont’d)
12. Programmed Night Stations can use CALL HOLD [C-6], CALL TRANSFER [C-10, 11] and THREE-
WAY CALLING [T-2], provided these features are programmed into the CLASS OF SERVICE -
INDIVIDUAL [C-15].
13. Operator calls after Consultation Hold is not transferred to the Night Station.
14. Individual Attendant calls are not transferred to the Night Station assigned by ATTENDANT NIGHT...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 29
Authorization Code A-20
A-20 Authorization Code
General Description
An AUTHORIZATION CODE is a numerical code dialed by users (up to 10 digits), which will override the station
CLASS OF SERVICE - INDIVIDUAL [C-15] for facility access restriction.
The AUTHORIZATION CODE can be masked on the D
termdisplay if necessary using the AUTHORIZATION
CODE DISPLAY ELIMINATION [A-99].
When a wrong code is received from a station/trunk, detailed...

NEAX2400 IPX Feature Programming ManualPage 30NDA-24297, Issue 1
A-20 Authorization Code
Service Conditions
1. A maximum of 10 digits for AUTHORIZATION CODE can be dialed, and 8 digits will be registered on
STATION MESSAGE DETAIL RECORDING [S-10].
2. The maximum number of AUTHORIZATION CODES is 4,000. This number is dependent upon system
configuration.
These specifications are based on the digits being assigned as follows:
1st digit: A (when A equals a unique digit from 0 - 9)
2nd digit: B - C (when b, c...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 31
Authorization Code A-20
Interactions (cont’d)
5. There are no restrictions regarding the first digit of AUTHORIZATION CODES, except what is
programmed in AMND. Tenant 0 does not conflict with the PBX numbering plan. This is true when
separate tenant tables are provided. If common tenant tables are used, a conflict between LCR(S) and
OGC(A), used with SMDR, will occur.
Note:The access code to the service feature AUTHORIZATION CODE must be...

NEAX2400 IPX Feature Programming ManualPage 32NDA-24297, Issue 1
A-20 Authorization Code
Programming (cont’d)
System Data 1, Index 13. Each Bit in Index 13 directly correlates to a digit in the AUTHORIZATION
CODE assigned in AATC, and will determine the second digit of the Checksum method. Pick any Bits
0 - 4, but not the same combination of Bits as picked in Index 12.
System Data 1, Index 14 determines the algorithm used to calculate the last two digits of every
AUTHORIZATION CODE. (Only decimal numbers...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 33
Authorization Code A-20
Programming (cont’d)
STEP 2:ANPD- Reserve a number level for feature access. Assign for Normal (N), Hooking (H), and Busy
(B) (if applicable to any feature in this level). Assign NND in accordance with a predetermined
numbering plan.
STEP 3:ASPA- For SRV = SSC (Service Code), SID = 42, assign the access code. For the NND parameter, no
assignment is required when AUTHORIZATION CODE operates by itself. When Account...

NEAX2400 IPX Feature Programming ManualPage 34NDA-24297, Issue 1
A-20 Authorization Code
FCCS Programming (cont’d)
STEP 3:LATCL- List up all the AUTHORIZATION CODES. This is the simplest way to determine what
digits have been added to the system with the Checksum method. This is not required if the Checksum
method is not used.
Note:When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN. 

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 35
Automatic Trunk Test A-21
A-21  Automatic Trunk Test
General Description
The AUTOMATIC TRUNK TEST capability provides a functional test on a large number of trunks at a prearranged
time. The results of the test are reported at the MAINTENANCE ADMINISTRATION TERMINAL (MAT) [M-
18]. The test can include: Ringback Tone Test, 1 KHz Test Tone and Trunk Selection Test, by having the proper test
trunk termination at the distant office.
Operating...

NEAX2400 IPX Feature Programming ManualPage 36NDA-24297, Issue 1
A-21 Automatic Trunk Test
Programming
STEP 1:ANPD- Reserve a number level for service feature access. Assign for Normal (N), Assign NND in
accordance with a predetermined numbering plan.
STEP 2:ASPA- The access code for INDIVIDUAL TRUNK ACCESS must be assigned, SID = 17. Assign
Connection Index, CI = (N) Normal. NND is assigned in accordance with a predetermined numbering
plan.
STEP 3:ARSC- A Route Restriction Class (RSC) must be...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 37
Authorization Code - Tie Line Incoming Routes A-29
A-29  Authorization Code - Tie Line Incoming Routes
General Description
This service feature offers an outside party the ability to enter an AUTHORIZATION CODE [A- 20] through an
incoming TIE Line trunk.
Operating Procedure
When the incoming route is restricted or when an AUTHORIZATION CODE [A-20] is always required
1. The called number, office code, and terminal number are received by the...