NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 48NDA-24297, Issue 1
A-53 All Zone Paging
A-53  All Zone Paging
General Description
This feature provides both the Attendant and a user with dial access to multiple zone paging equipment.
Operating Procedure
To operate from a station
1. The station goes off-hook; receives dial tone.
2. The station dials the ALL-ZONE PAGING access code.
3. Connections to multiple paging equipment are established.
Service Conditions
1. This feature allows only Paging access....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 49
All Zone Paging A-53
Interactions (cont’d)
8. ALL-ZONE PAGING is not possible from CONSULTATION HOLD [C-17].
9. CALL HOLD [C-6]: A Paging trunk cannot be placed on Call Hold.
10. The D
termLCD display indicates BUSY when the Paging trunk is Busy. Reorder tone is returned.
11. If Priority Page is to be used with ALL-ZONE PAGING in ARTD, CDN 6:TCL must be assigned as Data
8, Page with ringback tone. SYS1, Index 73 affects the operation of...

NEAX2400 IPX Feature Programming ManualPage 50NDA-24297, Issue 1
A-59 Announcement Service - Attendant
A-59  Announcement Service - Attendant
General Description
This feature allows the Attendant, via the ATTENDANT CONSOLE [A-3], to hear a prearranged announcement
when the Attendant dials a predetermined access code.
Operating Procedure
1. Press an idle loop key.
2. Dial the announcement trunk access code.
3. Listen to the message from announcement machine.
Service Conditions
1. This feature requires one...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 51
Announcement Service - Attendant A-59
Programming (cont’d)
STEP 6:MBTK- Assign the Make Idle status to the announcement trunk.
STEP 7:ARRC- If TIE Line, DID, or REMOTE ACCESS TO PBX [R-2] connection to the Announcement
Service trunk is required, allow trunk-to-trunk connection using ARI-D-RES=1 (Direct Connection is
allowed.)
STEP 8:AAED- This command is used to assign announcement equipment.
Dead Level:
Assign:
TN: Tenant Number
EQP:...

NEAX2400 IPX Feature Programming ManualPage 52NDA-24297, Issue 1
A-59 Announcement Service - Attendant
FCCS Programming (cont’d)
EQP: Announcement Equipment Number
0=DeadLevel
1 = Unused Number
2-15 = Announcement service
C: Duration of Connection
0 = Disconnection occurs in 30 seconds
1 = Connection is held until the station releases. See the requirements of the application for
the announcement equipment. For Dead level applications, data 0 is assigned.
R: Sending RBT
0/1 = Yes/No
A: Answer Signal...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 53
Attendant-To-Attendant Calling A-60
A-60 Attendant-To-Attendant Calling
General Description
This feature permits an Attendant, via an ATTENDANT CONSOLE [A-3], to access a non-specific free Attendant
by dialing the operator access code, or to call a particular ATTENDANT CONSOLE [A-3] by dialing an individual
Attendant Identification Number.
Operating Procedure
1. Press an idle loop key.
2. Dial the individual Attendant Identification Number...

NEAX2400 IPX Feature Programming ManualPage 54NDA-24297, Issue 1
A-60 Attendant-To-Attendant Calling
FCCS Programming (cont’d)
STEP 3:ALGNN- This command must be set to the NCN.
STEP 4:ASATN- This command must be set to the NCN. Assign identification numbers to the specific
Attendant Consoles.
Note:When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN. 

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 55
Automatic Idle Return A-69
A-69  Automatic Idle Return
General Description
This feature enables a Dtermto become idle automatically after the predetermined time when the line is released by
the opposite station on-hook, etc., on hands-free or the speaker operation.
Operating Procedure
No manual operation is required.
Service Conditions
1. This service may be assigned at each terminal.
2. This service is not available when the station has a...

NEAX2400 IPX Feature Programming ManualPage 56NDA-24297, Issue 1
A-78 Automatic Number Identification (ANI)
A-78  Automatic Number Identification (ANI)
General Description
This feature automatically sends the Calling Subscribers number to the called party after a response is received from
the distant office. This feature is used for outgoing CO calls (e.g., Enhanced 911 (E911) calls) or TIE Line calls using
DTMF signaling.
Operating Procedure
No manual operation is required. Automatic Number...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 57
Automatic Number Identification (ANI) A-78
Service Conditions (cont’d)
7. Other interactions are the same as for DTMF signal dialing.
8. FCCS link is not available for this feature.
Programming
STEP 1:ARTD- Assign route class data to the route number of the outgoing trunk.
RT:1
1-OSGS :7 2-ONSG :4 3-ISGS :7 4-INSG :4 15-LSG :5
19-EANI :1
STEP 2:AAND- Assign ANI sending digit as per the route number and the number of digits of the caller’s...