NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage 38NDA-24297, Issue 1
A-29 Authorization Code - Tie Line Incoming Routes
Interactions (cont’d)
6. If ASPA, SRV: LCR (Least Cost Route Selection) / LCRS (Register Sender LCR) AH parameter is
assigned as data“1”, the request for an AUTHORIZATION CODE is determined by the ARSC
assignment of the station in relationship to the route chosen. For AUTHORIZATION CODE - TIE LINE
INCOMING ROUTES, no RSC is assigned against the incoming TIE Line, therefore,
AUTHORIZATION...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 39
Authorization Code - Tie Line Incoming Routes A-29
Programming (cont’d)
ASYD- System Data 1, Index 14 determines the algorithm used to calculate the last two digits of
every AUTHORIZATION CODE. (Only decimal numbers may be used in this index, therefore,
hexadecimal values A to F may not be assigned).
System Data 1, Index 14 = X & Y, where X and Y represent any arbitrarily chosen decimal digit 1- 9,
and where Y is used to determine the...

NEAX2400 IPX Feature Programming ManualPage 40NDA-24297, Issue 1
A-29 Authorization Code - Tie Line Incoming Routes
Programming (cont’d)
Note:Procedure 1 is not available with AUTHORIZATION CODE - TIE LINE INCOMING ROUTES. For
example:
45 - 26428 - 623423 - 9-1-617-555-2323
(ACC) (AUTH CODE) (ACCOUNT CODE) (DESTINATION CODE)
ASPA ACC = 45 NND = 8 (ACC+ACCOUNT CODE)
For SRV = LCR (Least Cost Route Selection) / LCRS (Register Sender LCR), if operating Procedure 2 is
used, (dialing the AUTHORIZATION CODE...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 41
Authorization Code - Tie Line Incoming Routes A-29
FCCS Programming (cont’d)
STEP 2:ASPAL- For SRV = SSC (Service Code) SID = 42, assign the access code. For the NND parameter,
no assignment is required when AUTHORIZATION CODE [A-20] operates by itself. When Account
Code [A-18] operates with AUTHORIZATION CODE - TIE LINE INCOMING ROUTES, assign for
SRV = SSC (Service Code), SID = 42. The NND value will include the number of digits in the...

NEAX2400 IPX Feature Programming ManualPage 42NDA-24297, Issue 1
A-30 Automatic/Manual Intercom
A-30 Automatic/Manual Intercom
General Description
This feature permits multiple Dtermusers to simultaneously call all the stations in a preassigned group, regardless of
their idle/busy status. An INTERCOM member can optionally override another INTERCOM station in a two-party
INTERCOM connection. This service is referred to as INTERCOM BRIDGE. INTERCOM service is separated into
two types, AUTOMATIC INTERCOM...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 43
Automatic/Manual Intercom A-30
Operating Procedure (cont’d)
To bridge into a Manual Intercom call
1. When two stations are engaged in an INTERCOM call, a third station, belonging to the same INTERCOM
group, will press the MICM key and go off-hook.
2. A three-party conference is established. The called stations may hear a Warning Tone when the station
bridges into the call. This Warning Tone is preassigned in system data.
Use of the SIG...

NEAX2400 IPX Feature Programming ManualPage 44NDA-24297, Issue 1
A-30 Automatic/Manual Intercom
Interactions (cont’d)
3. The AICD Command must be assigned before the AKYD command.
4. When assigning the PRI parameter in AKYD, the following data selections are available.
5. No programming is required to enable the SIG key to remain active at all times.
6. The SIG key, when pressed by a calling station, will interrupt other ringing signals at the called station.
7. Hands-Free operation is available with...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 45
Automatic/Manual Intercom A-30
Programming (cont’d)
RING: 0: No Ringing
1: Ringing - All Lines
2: Ringing on Prime Line Only
3: Flexible Ring Assignment, enables RG parameter
PRI: Form of Line Preference (0-3)
KYN: Key Number (1-40)
KYI: Service Index
0: Key not used
1: Feature Key
2: Multi-line Key
KD: Kind of Line
0: Multi-line
1: INTERCOM Line
ICM: Kind of INTERCOM
0: AUTOMATIC INTERCOM
1: MANUAL INTERCOM
2: DIAL INTERCOM
If Manual...

NEAX2400 IPX Feature Programming ManualPage 46NDA-24297, Issue 1
A-52 Account Code - Attendant
A-52  Account Code - Attendant
General Description
This feature provides the ATTENDANT CONSOLE [A-3] with the capability to enter an Account Code into the
system after talking with a CO outgoing/incoming call.
Operating Procedure
The Attendant talks with the CO trunk call
1. Press the START key.
2. Dial the Account Code feature access code. Service set tone is heard.
3. Dial the Account Code (up to 10 digits)....

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 47
Account Code - Attendant A-52
Programming (cont’d)
For example:
44 - 623423 - 511234 - 617 - 555 - 2323
2+0+6= 8
ACC + AUTH CODE + ACCT CODE = NND
STEP 4:ASFC- For stations to use ACCOUNT CODE, assign a Class of Service that allows SFI 27.
STEP 5:AMND- If Authorization Codes are used with ACCOUNT CODES, then for Tenant 0, assign the
Destination Code (DC) as the first digit of all Authorization Codes and the Maximum Necessary Digits
(MND)...