NEC Neax 2400 Ipx Feature Programming Manual

NEAX2400 IPX Feature Programming ManualPage xxivNDA-24297, Issue 1
I-17Individual Attendant Access - CCISXX X*
I-18Inter-Position Transfer - CCISX——
L-25Look Ahead Routing - CCISXX X
L-29LDN Night Connection - CCISXX X
M-34Message Reminder - CCISXX N
M-34D
Message Reminder - D
term-CCISXX N
M-35Message Waiting Lamp Setting - Attendant - CCISXX X
M-36Message Waiting Lamp Setting - Station - CCISXX X
M-37Miscellaneous Trunk Access - CCISX—X
M-38Miscellaneous Trunk Restriction - CCISX—N
M-39Modem Pooling -...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page xxv
Note 1:* This feature is available on the condition that the NEAX2000 IVS2is the satellite office.
Note 2:** Only 2 modes of Day/Night are available for NEAX2000 IVS2.
Note 3:Telephone numbers should be used for activating CCIS services through FCCS groups and a NEAX2000
IVS2. R-22Restriction from Outgoing Calls - CCISXX X
S-52Serial Call - CCISXX N
S-53D
Service Display - D
term-CCISX—N
S-54Simultaneous Voice and Data Transmission -...

NEAX2400 IPX Feature Programming ManualPage xxviNDA-24297, Issue 1
This page is for your notes. 

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 1
Attendant Camp-On with Tone Indication A-1
A-1  Attendant Camp-On with Tone Indication
General Description
This feature permits the Attendant, when a desired station is busy, to hold an incoming call in a special waiting
mode. The Attendant sends a distinctive Camp-On Tone Indication to the busy station. When that station becomes
idle, it is automatically rung and connected to the waiting trunk party upon answering.
Operating Procedure
To...

NEAX2400 IPX Feature Programming ManualPage 2NDA-24297, Issue 1
A-1 Attendant Camp-On with Tone Indication
Service Conditions (cont’d)
CALL WAITING - ORIGINATING [C-31]
CALL WAITING - TERMINATING [C-12]
CONSULTATION HOLD - ALL CALLS [C-17, C-17D]
DATA LINE SECURITY [D-12]
DATA PRIVACY ON DEMAND [D-17]
DIAL ACCESS TO ATTENDANT [D-2]
EXCLUSIVE HOLD - D
term[E-4D]
EXECUTIVE RIGHT-OF-WAY [E-1, E1D]
NON-EXCLUSIVE HOLD - D
term[N-7D]
OFF-HOOK QUEUING [O-7]
OUTGOING TRUNK QUEUING [O-2, O-2D]
PRIVACY - D...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 3
Attendant Camp-On with Tone Indication A-1
Interactions
1. System Data 2, Index 2, Bit 5 will enable ATTENDANT LOOP RELEASE [A-6], which allows 12 calls
to be camped-on to stations by Attendant Console.
2. The Attendant Console must first be provided.
3. Route Restrictions disallowing a call to terminate at a station will also disallow ATTENDANT CAMP-
ON.
4. STATION HUNTING [S-7, 8, 9] and UNIFORM CALL DISTRIBUTION [U-1] take precedence...

NEAX2400 IPX Feature Programming ManualPage 4NDA-24297, Issue 1
A-2 Attendant-Controlled Conference
A-2 Attendant-Controlled Conference
General Description
This feature permits the Attendant to establish a conference among as many as eight parties. The conferees may
consist of any combination of stations and/or trunks, whether inside or outside parties.
Operating Procedure
1. Station calls Attendant to request conference.
2. Attendant connects a party to one of the assigned line circuits.
3. Attendant...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 5
Attendant-Controlled Conference A-2
Programming (cont’d)
2: PB
3: DP/PB
12: D
term
13: Data terminal Via Dterm
14: Hot Line
15: CAS Line
16: Data Terminal Via Data Module
18: Virtual Circuit
23: ISDN Terminal
26: VPS
27: Eight Conference Equipment
RSC: Route Restriction Class (0-15)
For assignment of RSC, ARSC command.
SFC: Service Feature Class (0-15)
For assignment of SFC, ASFC command.
STEP 2:ASHP- Assign a Pilot hunting group using the...

NEAX2400 IPX Feature Programming ManualPage 6NDA-24297, Issue 1
A-3 Attendant Console
A-3 Attendant Console
General Description
The ATTENDANT CONSOLE operates on a switched loop basis. Six Attendant loops terminate at each console
via the associated position circuit. The Attendant can answer, originate, hold, extend and re-enter calls through each
loop. The number of calls may be effectively increased to 12 through use of the ATTENDANT LOOP RELEASE
[A-6] feature.
Operating Procedure
Refer to the...

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 7
Attendant Console A-3
Service Conditions (cont’d)
15. A PA-CS33 circuit card is required. The switch setting for PA-CS33 (ATI) is shown below:
16. The Attendant Console must be accommodated in one LN only when used in the IPX-U system.
17. A terminating node (FPC) must be assigned in the FCCS network.
18. Identical system data related to Attendant Console should be programmed at all nodes.
19. A different destination for C.O. incoming call...