NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 827
Centralized System Management Report - CCIS C-57
Service Conditions (cont’d)
(Series 7400 software enhancement) Service Conditions when this service is provided in the network
through FCCS groups and NEAX2000 IVS:
1.(Series 7400 software enhancement) The Centralized System Message Report feature for this network
may be controlled only by the Centralized MAT.
Note:
See Centralized Maintenance - CCIS [C-167] for explanation of the...

NEAX2400 IMX Feature Programming Manual
Page 828ND-70184 (E), Issue 3
C-57 Centralized System Management Report - CCIS
Programming (cont’d)
System 1, Index 86, Bit 4. Assign Fault Data Automatic Printout Function (Automatic output to the
Printer) (1).
System 1, Index 86, Bit 7: Assign Fault Message-0/1: Simplified Registration/Detailed Registration.
System 1, Index 91, Bits 2 & 3: Assign System Message Output Grade. 
0: All
2: Higher than Grade 2 (MN, MJ) 
3: Higher than Grade 3 (MJ) 
System 1, Index...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 829
Consultation Hold - All Calls - CCIS C-58
C-58  Consultation Hold - All Calls - CCIS
General Description
This feature permits a user within the CCIS network to hold any incoming or outgoing public network, intra-office,
or CCIS call while originating a call to another station within the CCIS network.
Operating Procedure
To hold the original call and place a second call from a single-line telephone:
1. Switch hook flash; receive...

NEAX2400 IMX Feature Programming Manual
Page 830ND-70184 (E), Issue 3
C-58 Consultation Hold - All Calls - CCIS
Interactions
1. This feature is denied whenever the destination telephone set is engaged in any state other than simple two-
party connection. 
2. CONSULTATION HOLD-ALL CALLS - CCIS must always be made available when features require
hooking services.
3. Indexes 156 and 157 also are used for SMDR, establishing an arbitrary connection timing when no answer
supervision is used. 
4. If a party is...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 831
Consultation Hold - All Calls - CCIS C-58
Programming
ASYD - System Data 1, Index 156. Trunk Soft Hold Timer A, used with second dial tone trunks.
Assign data 00H for 30 seconds. (Data 31H may be used for a value of two seconds if CALL
TRANSFER-ALL CALLS [C-50] is to be used immediately after connecting to the trunk.) This is the
time between trunk connections when switch hook flash is allowed on a non-senderized trunk
connection....

NEAX2400 IMX Feature Programming Manual
Page 832ND-70184 (E), Issue 3
C-94 Call Forwarding Assignment - Attendant - CCIS
C-94  Call Forwarding Assignment - Attendant - CCIS
General Description
This feature allows the attendant of an Attendant Console to set/cancel the following Call Forwarding services to a
station within the CCIS network.
CALL FORWARDING-ALL CALLS [C-5]
CALL FORWARDING-ALL CALLS - CCIS [C-45]
CALL FORWARDING-BUSY LINE [C-2]
CALL FORWARDING-BUSY LINE - CCIS [C-46]
CALL FORWARDING-DON’T...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 833
Call Forwarding Assignment - Attendant - CCIS C-94
Service Conditions (cont’d)
a.) Pattern 1 (ASYD, SYS2, INDEX 15, b4= 0)
XX
 - XX - XXXXX - XXXXX
This pattern is used when a unified numbering plan is in use within the CCIS network.
b.) Pattern 2 (ASYD, SYS2, INDEX 15, b4 = 1)
XX
 - XX - XXXXX - XXXXX - #
This pattern is used when a unified numbering plan is not in use within the CCIS network.
2. Since the numbering plan at the...

NEAX2400 IMX Feature Programming Manual
Page 834ND-70184 (E), Issue 3
C-163 CCIS Networking via IP
C-163 CCIS Networking via IP
            (Series 7400 software feature)
General Description
This feature allows the system to utilize the CCIS network over Internet/Intranet. To establish or release a call,  an
IPTRK card is used for both speech and signal channels.
Operating Procedure
No manual operation is required.
Service Conditions
1. To send or receive speech and CCIS signals, each node shall use an...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 835
CCIS Networking via IP C-163
Service Conditions (cont’d)
10. The table below shows CCIS service features to be provided beyond the nodes:
11. This feature does not support Broad Band Services H0/H1.
12. This feature can use Link Re-connection function. At this time, service conditions are the same as those
for the normal CCIS network.
13. PAD can be provided for “receive” control only.
14. IPTRK-related tandem connection is not...

NEAX2400 IMX Feature Programming Manual
Page 836ND-70184 (E), Issue 3
C-163 CCIS Networking via IP
Programming
STEP 1:Referring to the No. 7 CCIS System Manual, assign the entire basic data (such as ASYD, ARTD,
ATRK, ADPC, ACSC, ACIC1, ACIC2, MBTK, etc.) necessary for the establishment of a CCIS Tie
Line.
Enter IPTRK = 1 for both D-channel and B-channel routes on the ARTI command.
For the port assignment (B-ch) of the IPTRK card, see the IPTRK Circuit Card System Manual.
The CCIS signal controlling...