NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 817
Call Transfer - Attendant - CCIS C-54
C-54 Call Transfer - Attendant - CCIS
General Description
This feature allows a user to transfer a call through the CCIS network to an Attendant Console located in a Main or
Satellite node, while connected to a CCIS network call. 
Operating Procedure
To transfer a call to an Attendant Console: 
1. While engaged in a Central Office trunk call, switch hook flash; receive special dial tone.
2. Dial...

NEAX2400 IMX Feature Programming Manual
Page 818ND-70184 (E), Issue 3
C-54 Call Transfer - Attendant - CCIS
Interactions (cont’d)
4. A call transfer to a Dterm that has DO NOT DISTURB [D-21D] set will receive reorder tone, or follow
CALL FORWARDING-BUSY LINE or ALL CALLS if set.
Programming
STEP 1:ASYD - System Data 2, Index 1, Bits 0 & 1. Assign data “11” to allow CONSULTATION HOLD [C-
58] for all types of connections.
STEP 2:AT N R - Allow tenant-to-tenant connection for Inter and Intra-tenant...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 819
Centralized Billing - CCIS C-55
C-55  Centralized Billing - CCIS
General Description
This service is used for collecting billing information from each office within the network and directing it to
associated offices, thus providing the billing information to the CENTRALIZED BILLING CENTER via an RS-
232C interface.
(Series 7400 software enhancement) This feature may be provided through multiple FCCS groups (networks
where multiple...

NEAX2400 IMX Feature Programming Manual
Page 820ND-70184 (E), Issue 3
C-55 Centralized Billing - CCIS
Operating Procedure (cont’d)
2. Station C goes off-hook; Stations A and C are connected with each other in conversation.
3. Stations A and C go on-hook; SMDR information is sent out to the CENTRALIZED BILLING CENTER.
4. Station B dials Station C in Node C; Station B receives ringback tone and Station C is rung.
5. Station C goes off-hook; Stations B and C are connected in conversation.
STN (c)
STN (a)...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 821
Centralized Billing - CCIS C-55
Operating Procedure (cont’d)
6. Stations C and B go on-hook; SMDR information is sent to the Billing Center through the CCIS line.
Service Conditions 
1. The maximum number of billing information output ports at the Center Office is 2.
2. Information storage capacity of the office should be 700 calls.
3. If billing information in excess of the above mentioned storage capability is generated at a time...

NEAX2400 IMX Feature Programming Manual
Page 822ND-70184 (E), Issue 3
C-55 Centralized Billing - CCIS
Service Conditions (cont’d)
Legend:
* Destination node
** Node to be connected to the FCCS group where the new number is added
*** Node where the telephone number is located before the Number Portability activation
No.Pattern (telephone number is moved from A to B)Node Requiring Data Change
1. Moving number within the same FCCS group. NCN in Center FCCS group
2. Moving number in FCCS group to another...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 823
Centralized Billing - CCIS C-55
Programming
STEP 1:ASYD - System 1, Index 32, Bit 0: At the time of SMDR processor trouble, outgoing call is not
restricted/restricted = 0/1. Bit 1: Tenant information is recorded (1). Bit 2: Route information is
recorded (1). Bit 7: SMDR services are provided (1).
System 1, Index 33, Bits 3 & 4: Designation of a total of parties to be billed. Bit 5: Designation of
billing system for a transferred...

NEAX2400 IMX Feature Programming Manual
Page 824ND-70184 (E), Issue 3
C-56 Centralized Day/Night Mode Change - CCIS
C-56  Centralized Day/Night Mode Change - CCIS
General Description
This service feature switches the DAY/NIGHT mode of Satellite Nodes which are linked to the Main Node via
CCIS, in accordance with the DAY/NIGHT mode switching [A-3] at the Main Node.
Operating Procedure
Note:
Node B - Node E are Satellite Nodes.
1. Press the NIGHT key on the Attendant Console for each Tenant; the NIGHT lamp...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 825
Centralized Day/Night Mode Change - CCIS C-56
Service Conditions (cont’d)
4. At a Satellite Node, only TN = 1 is possible.
5. When a Satellite Node is equipped with DAY/NIGHT mode changeover features, changeover of the
Satellite Node DAY/NIGHT mode is not performed from the Main Node. 
6. The Satellite Node cannot have an Attendant Console programmed.
7. Selecting DAY/NIGHT option from the NEAX2400 IMX does not change the NEAX2000 IVS...

NEAX2400 IMX Feature Programming Manual
Page 826ND-70184 (E), Issue 3
C-57 Centralized System Management Report - CCIS
C-57  Centralized System Management Report - CCIS 
General Description
This service feature provides automatic reporting of fault information of Satellite Nodes to the CENTRALIZED
MANAGEMENT CENTER with an external indication of the detected fault.
(Series 7400 software enhancement) This feature may be provided through multiple FCCS groups (networks
where multiple NEAX2400 IMXs are...