NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 777
Busy Verification - CCIS B-9
Interactions (cont’d)
4. ATTENDANT LOCKOUT [A-5]: The Attendant is prevented from verifying a busy station line that is
connected to a loop held at the Attendant Console. Since the LOCKOUT feature applies only to calls held
on an Attendant Console loop, BUSY VERIFICATION - CCIS of those station lines will be denied, and
the Attendant will hear reorder tone.
5. CALL FORWARDING - CCIS (ALL CALLS [C-45], BUSY...

NEAX2400 IMX Feature Programming Manual
Page 778ND-70184 (E), Issue 3
B-9 Busy Verification - CCIS
Programming (cont’d)
STEP 2:ASFC - For stations that permit BUSY VERIFICATION, assign a Class of Service that allows SFI 4,
EXECUTIVE RIGHT-OF-WAY [E-1] and SFI 11, ATTENDANT CAMP-ON WITH TONE
INDICATION [A-45]. SFI: 3 must be allowed for the attendant’s Service Feature Class (normally
SFC: 0) at all locations allowing the attendant to use this feature. 
STEP 3:AT R K - Assign the LEN as Route 909, Digital...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 779
Brokerage Hotline - CCIS B-10
B-10  Brokerage Hotline - CCIS 
General Description
This feature provides a hotline function between two stations at different nodes in the CCIS network, using a line/
feature key of a Dterm.
Operating Procedure
To access a BROKERAGE HOTLINE - CCIS from a Dterm:
1. Lift the handset or press the SPEAKER button. 
2. Press the line/feature key associated with a predetermined station in another office. The...

NEAX2400 IMX Feature Programming Manual
Page 780ND-70184 (E), Issue 3
B-10 Brokerage Hotline - CCIS
Service Conditions (cont’d)
12. If the destination station is busy and is a pilot member of a UCD group, the UCD function will be activated.
If all stations in the UCD group are busy, ringback tone will be heard, or if programmed, DELAY
ANNOUNCEMENT-UCD [D-31] or OVERFLOW-UCD [O-13] will be invoked.
13. CALL FORWARDING-ALL CALLS [C-5] [C-45], CALL FORWARDING-BUSY LINE [C-2] [C-46],
and CALL...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 781
Brokerage Hotline - CCIS B-10
Programming (cont’d)
KYN: Key Number (1-16) 
KYI: Service Index 
0: Key Not Used 
1: Feature Key 
2: Multi-line Key 
KD: 0
RG: Ringing Assignment per Multi-line Appearance 
0: No Ringing. 
1: Ringing in Day Mode Only. 
2: Ringing in Night Mode Only. 
3: Ringing Day and Night. 
STEP 4:ASPD - Assign the tenant Abbreviated Digit Code (ADC), and Digit Code (DC).
STEP 5:ASFC - Primary station and Hotline must...

NEAX2400 IMX Feature Programming Manual
Page 782ND-70184 (E), Issue 3
C-44 Call Back - CCIS
C-44  Call Back - CCIS 
General Description
This service feature allows an Inter-office Call Back when the calling station and the called station respectively
belong to a different PBX in the CCIS network. 
Operating Procedure
To set from a Single-Line Telephone:
1. Dial the desired telephone number; receive busy tone.
2. Switch hook flash; receive special dial tone.
3. Dial the CALL BACK - CCIS code; receive...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 783
Call Back - CCIS C-44
Operating Procedure (cont’d)
3. The LCD will display: 
Service Conditions 
1. If CALL BACK is not answered within 30 seconds, or the timer interval in ASYD index 139, ringing will
stop and the CALL BACK will automatically be cancelled.
2. CALL BACK to a busy station cannot be established if the station is in the LINE LOCKOUT [L-3] mode. 
3. There is no time limit for CALL BACK once activated. It will remain in...

NEAX2400 IMX Feature Programming Manual
Page 784ND-70184 (E), Issue 3
C-44 Call Back - CCIS
Interactions 
1. OUTGOING TRUNK QUEUING [O-2] and CALL BACK - CCIS cannot be accessed simultaneously.
2. System Data 1, Index 139. No Answer Timer is also used for station-to-station call, DID, or TIE Line call
for CALL FORWARDING-DON’T ANSWER [C-47] and CALL HOLD [C-6].
3. CALL WAITING-ORIGINATE [C-31] automatic setting and CALL BACK - CCIS are mutually
exclusive.
4. CALL BACK - CCIS cannot be activated toward...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 785
Call Forwarding - All Calls - CCIS C-45
C-45  Call Forwarding - All Calls - CCIS
General Description
This service feature allows Inter-Office CALL FORWARDING-ALL CALLS when the transferring station and the
transferred station, respectively, belong to a different PBX in the CCIS network. 
Operating Procedure
When setting Call Forwarding-All Calls Service:
1. Station A goes off-hook; receives dial tone.
2. Station A dials the Access...

NEAX2400 IMX Feature Programming Manual
Page 786ND-70184 (E), Issue 3
C-45 Call Forwarding - All Calls - CCIS
Operating Procedure (cont’d)
6. Station B answers; Stations B and C are connected with each other.
When cancelling Call Forwarding-All Calls Service:
1. Station A goes off-hook; receives dial tone.
2. Station A dials the Cancel Code of Call Forwarding-All Calls; receives service set tone.
3. Station A hangs up. 
Service Conditions
1. Stations with this feature set may originate calls and access...