NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 747
Variable Timing Parameters V-1
V-1 Variable Timing Parameters
General Description
The Variable Timing Parameters feature gives the PBX the versatility to change timing parameters, using the
MAINTENANCE ADMINISTRATION TERMINAL (MAT) [M-18]. All timing parameters for a specific timing
sequence are set initially within the generic program. These timing parameters can be changed to accommodate user
requirements. 
Operating Procedure
No...

NEAX2400 IMX Feature Programming Manual
Page 748ND-70184 (E), Issue 3
V-1 Variable Timing Parameters
Interactions
1. To calculate VARIABLE TIMING PARAMETERS, multiply the Timer Class by the Miscellaneous
Timer Class, TC x MTC = VARIABLE TIMING PARAMETER. TC is a set value. MTC is any value
from 1-15, assigned in hexadecimal. For the PERIODIC TIME INDICATION TONE Timer, a TC of 3
equaling 2 seconds is not available, but a TC of 4 equaling 30 seconds is available.
Timer Index:
TC values for Indexes 136,...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 749
Variable Timing Parameters V-1
Interactions (cont’d)
TC values for Indexes 142, 143, 144 
TC 0 = -
1 = -
2 = -
3 = 2 seconds
4 = 30 seconds 
7 = 8 seconds.
TC values for Indexes 135 
TC 0 = -
1 = 64 msec.
TC values for Indexes 149 
TC 0 = -
1 = -
2 = -
3 = 2 seconds
4 = 30 seconds. 
TC values for Indexes 145 
TC 0 = -
1 = 2 seconds.
Programming
ASYD - System Data 1. All VARIABLE TIMING PARAMETERS are located between Indexes 128
and...

NEAX2400 IMX Feature Programming Manual
Page 750ND-70184 (E), Issue 3
V-2 Voice Call
V-2 Voice Call
General Description
This feature enables a single line telephone to make a VOICE CALL [V-2] when the called party is a Dterm set. This
path exists from the calling party to the called partys built-in speaker. If the called partys MIC is on, the called party
can converse hands-free.
Operating Procedure
From a single line station to a Dterm:
1. Dial the telephone number of the desired Dterm station and...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 751
Voice Call V-2
Programming (cont’d)
For a Dterm:
STEP 1:AKYD - Assign the station according to the following parameters:
TN: 1
STN: Station Number 
TP: Type of D
term 0/1:
RING: 
0: No Ringing 
1: Ringing All Lines 
2: Ringing on Prime Line Only 
3: Flexible Ring Assignment, enables RG parameter.
KYN: Key Number (1-40) 
KYI: Service Index 
0: Key Not Used 
1: Feature Key 
2: Multi-line Key 
KD: Not assigned for Feature Key 
FKY:...

NEAX2400 IMX Feature Programming Manual
Page 752ND-70184 (E), Issue 3
V-2D Voice Call - Dterm
V-2D Voice Call - Dterm
General Description
This feature provides a voice path between two Dterm sets. This path exits from the calling party to the called party’s
built-in speaker. If the called party’s MIC key is on, the called party can converse hands-free. 
Operating Procedure
From one Dterm to another Dterm:
1. The originating Dterm user dials the desired telephone number and receives a ringback tone. 
2....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 753
Voice Call - DtermV-2D
Interactions
A Voice Call cannot be sent to a single-line station. 
Programming
Operating with the feature key:
STEP 1:AKYD - Assign the station according to the following parameters:
TN: 1 
STN: Station Number 
TP: Type of D
term 0/1:
RING: 
0: No Ringing 
1: Ringing All Lines 
2: Ringing on Prime Line Only 
3: Flexible Ring Assignment, enables RG parameter.
KYN: Key Number (1-40) 
KYI: Service Index 
0: Key...

NEAX2400 IMX Feature Programming Manual
Page 754ND-70184 (E), Issue 3
V-3D Volume Control - Dterm
V-3D Volume Control - Dterm
General Description
This feature is used for controlling the volume of a Dterm set’s built-in speaker and receiver.
Operating Procedure
1. The Dterm set is equipped with a sliding volume control knob located in the front, beneath the dial pad.
Volume can be increased by moving the control to the right, and decreased by moving it to the left.
2. The ringing volume is controlled by...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 755
WATS Access W-1
W-1 WATS Access
General Description
This feature permits any user direct-dial access to outgoing WATS lines.
Operating Procedure
1. Lift the handset; receive dial tone.
2. Dial the WATS ACCESS code.
3. Receive second dial tone. 
4. Dial the desired number.
Service Conditions
Access to WATS lines may be denied to individual stations via CLASS OF SERVICE-INDIVIDUAL [C-15]. 
Interactions
1. WATS ACCESS will operate in...

NEAX2400 IMX Feature Programming Manual
Page 756ND-70184 (E), Issue 3
W-1 WATS Access
Programming (cont’d)
STEP 5:ASPA - Assign the access code as assigned in ANPD above. Type of Service, SRV = OGC (Outgoing
Call) Outgoing Trunk. Assign the route number associated with this access code. 
STEP 6:ARSC - The Route Restriction Class must be constructed to allow the station access to the involved
routes.