Home > NEC > Communications System > NEC Neax 2400 Imx Feature Programming Manual

NEC Neax 2400 Imx Feature Programming Manual

Here you can view all the pages of manual NEC Neax 2400 Imx Feature Programming Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 751

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 707
Toll Denial/Toll Diversion T-6
Programming (cont’d)
Bit 3- Develop ATDP command for Day/Night? 
System Data 2, Index 1, bits 4 & 5. If TOLL DENIAL is required, assign these bits as data “00”. If
TOLL DIVERSION is required, assign these bits as “01”. Calls are then diverted to the Attendant
Console. Assigned on a per-tenant basis. 
STEP 2:ARSC - Assign Route Restriction Classes. When these are assigned to stations, classes will...

Page 752

NEAX2400 IMX Feature Programming Manual
Page 708ND-70184 (E), Issue 3
T-6 Toll Denial/Toll Diversion
FCCS Programming (cont’d)
RES: Restriction Data 
0: Connection is Restricted
1: Connection is Allowed 
2: Connection is Toll Restricted (See TOLL RESTRICTION-3/6-DIGIT [T-7])
STEP 3:ASDTN - When assigning the data to specific stations, assign the proper RSC to each station.
Note:
When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required in addition
to ASYDL or ASYDN. 

Page 753

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 709
Toll Restriction - 3/6-Digit T-7
T-7 Toll Restriction - 3/6-Digit
General Description
This feature allows the NEAX2400 IMX to be programmed to restrict outgoing calls according to specific area and/
or central office codes. This restriction is controlled on the basis of a three-digit area code or a six-digit combination
area and office code numbering plan.
Operating Procedure
No manual operation is required.
Service Conditions 
1. The...

Page 754

NEAX2400 IMX Feature Programming Manual
Page 710ND-70184 (E), Issue 3
T-7 Toll Restriction - 3/6-Digit
Programming
Note:
The digits underlined are to be listed in the DC (Digit Code) parameter.
Overseas or Operator-assisted calls should be listed with an MND equal to the calculated number of required digits.
Special dialing sequences, such as, “911” with an MND = 4 should also be listed.
N = 2-9, P = 0 or 1, X = 0-9
STEP 1:AT D P - This command is used with the AARP command. It designates the digit codes...

Page 755

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 711
Toll Restriction - 3/6-Digit T-7
Programming (cont’d)
System Data 2, Index 1, Bits 4 & 5. If TOLL DENIAL (busy tone) is required, assign these Bits as data
“00”. If TOLL DIVERSION (to Attendant) is required, assign these Bits as “01”.
System Data 2, Index 1, Bit 7. Does TOLL RESTRICTION apply to SPEED CALLING-SYSTEM [S-
3]? 0/1: Yes/No.
STEP 3:ARSC - Assign Route Restriction Classes. When these are assigned to stations, classes will...

Page 756

NEAX2400 IMX Feature Programming Manual
Page 712ND-70184 (E), Issue 3
T-7 Toll Restriction - 3/6-Digit
Programming (cont’d)
Toll Restriction Examples: 
Several examples of the use of TOLL RESTRICTION are listed below:
RSC 1: Allow local only.
RSC 2: Allow local plus Area Codes 718, 212, 201, and 914.
RSC 3: Allow local plus Area Codes 718, 212, and 201; and office codes 239, 465, and 798 only
within Area Code 914.
RSC 4: Allow local plus all Area Codes except 808, 213, 408, and 714. 
RSC 5:  Allow local...

Page 757

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 713
Toll Restriction - 3/6-Digit T-7
Programming (cont’d)
DAY/NIGHT: D (Day) 
OGRT: 1 RSC: 3 
DC: 92 TDI: 1(Connection is Allowed)
Repeat these same assignments for Digit Codes “93” through “99” to allow all local office codes. 
To allow Area Codes 718, 212, and 201, repeat the ATDP command for the following Digit Codes:
DC: 91718 TDI: 1 (Connection is Allowed)
DC: 91212  TDI: 1 (Connection is Allowed)
DC: 91201 TDI: 1 (Connection is...

Page 758

NEAX2400 IMX Feature Programming Manual
Page 714ND-70184 (E), Issue 3
T-7 Toll Restriction - 3/6-Digit
Programming (cont’d)
DC: 914798 RES: 1 (Connection is Allowed) 
OGRT: 1 RSC: 3 FLAG: 2
DC: 718623 RES: 1 (Connection is Allowed)
DC: 718567 RES: 1 (Connection is Allowed) 
This allows just these office codes within these particular Area Codes. All other area codes beginning
with “7” or “9” are also restricted. At this point, if allowing Area code 714 is desired, assign AARP as
follows:
AARP
 Command-...

Page 759

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 715
Toll Restriction - 3/6-Digit T-7
Programming (cont’d)
ATDP Command-
TDM/OG: O (Outgoing Connection) 
DAY/NIGHT: D (Day) 
OGRT: 1 RSC: 5
DC: 92 TDI: 1 (Connection is Allowed) 
Repeat these same assignments for Digit Codes “93” through “99” to allow all local office codes.
TDM/OG: O (Outgoing Connection)
DAY/NIGHT: D (Day) 
OGRT: 1 RSC: 5 
DC: 912  TDI: 2 (Go to AARP Command) 
NND: 6
DC: 913 TDI: 2 NND: 6 
(Go to AARP Command)
DC: 914...

Page 760

NEAX2400 IMX Feature Programming Manual
Page 716ND-70184 (E), Issue 3
T-7 Toll Restriction - 3/6-Digit
Programming (cont’d)
Example 6 - Trunk-to-Trunk Connection
Allow all Local Calls
ATDP
 Command-
TDM/OG: T (Tandem Connection)
ICRT: Route 2 OGRT: 1
DC: 92 TDI: 1 (Connection is Allowed) 
Repeat these same assignments for Digit Codes “93” through “99” to allow all local office codes.
Notice that assignments for digit codes “90” and “91”, which cover operator calls and all 1 + Area
Code calls, are not...
Start reading NEC Neax 2400 Imx Feature Programming Manual

Related Manuals for NEC Neax 2400 Imx Feature Programming Manual

All NEC manuals