NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 727
Tenant Service T-12
Programming (cont’d)
Assignment of Tenant Restriction Class
TRI: Tenant Restriction Index
0: Allows intra and inter-tenant station calls. Allow calls within tenant.
1: Allows CALL FORWARDING-ALL CALLS, DON’T ANSWER, BUSY LINE on an
intra and inter-tenant basis. Allow this feature within tenant.
2: Not used.
3: Allows the CALL FORWARDING-ALL CALLS, DON’T ANSWER, and BUSY LINE
on an intra and inter-tenant basis as...

NEAX2400 IMX Feature Programming Manual
Page 728ND-70184 (E), Issue 3
T-18D Time Display - Dterm
T-18D  Time Display - Dterm
General Description
This feature provides a digital time display on a Dterm’s LCD.
Operating Procedure
No manual operation is required.
Service Conditions 
1. The time is displayed according to the clock in the PBX and is set via the MAINTENANCE
ADMINISTRATION TERMINAL (MAT) [M-18]. 
2. Time is displayed automatically:
3. Time is constantly displayed on the center line of the LCD....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 729
Trunk Line Appearance T-23
T-23 Trunk Line Appearance
General Description
This feature allows a Dterm user to directly access a Central Office trunk or TIE Line without dialing an access code.
Incoming calls can also be answered at the TRUNK LINE APPEARANCE [T-23].
Operating Procedure
To access an outgoing trunk:
1. Press the TRUNK LINE APPEARANCE line/feature key. 
2. Lift the handset or press the SPEAKER key. Central Office or...

NEAX2400 IMX Feature Programming Manual
Page 730ND-70184 (E), Issue 3
T-23 Trunk Line Appearance
Interactions (cont’d)
4. TRUNK LINE APPEARANCE and HOTLINE-OUTSIDE [H-9] are mutually exclusive. Both features
require the AHLS command, and the same station cannot be provided with two Hotline features.
Programming
STEP 1:ASDT - Assign the station with the TRUNK LINE APPEARANCE as a virtual line (TEC = 18). 
TN: Tenant Number 
STN: Station Number 
LENS: Line Equipment Number (6 digits)
TEC: Telephone Class...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 731
Trunk-to-Trunk Third-Party Cancellation T-28
T-28 Trunk-to-Trunk Third-Party Cancellation
General Description
This feature allows a station to cancel an active trunk-to-trunk connection (during a three-way-connection) and
return to the original call.
Operating Procedure
If a station is presently engaged in a call with another station or with a trunk party: 
1. Switch hook flash; receive special dial tone.
2. Dial a trunk access code...

NEAX2400 IMX Feature Programming Manual
Page 732ND-70184 (E), Issue 3
T-28 Trunk-to-Trunk Third-Party Cancellation
Programming (cont’d)
System Data 3, Index 2, Bits 4-7. Switch hook flash ends timer. To calculate this value: (1 ~ FH) x 120
msec = Timer. For both beginning and ending timers, assign 91H for 120 - 1080 msec.
FCCS Programming 
No unique programming is required for the FCCS network.
Note:
System timers may be set on a network basis in ASYDN.
f (t) Bit 0-3 Bit 4-7
0 ms
No Detection120 ms 1080...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 733
Timed Reminder T-62
T-62 Timed Reminder 
General Description
This feature allows a user to set a Timed Reminder call from the station. The system calls up the station at the
designated time. When the station answers the call, the user hears a message or Music-On-Hold.
Operating Procedure
To set a Timed Reminder call:
1. Lift a handset; receive dial tone.
2. Dial the Timed Reminder (SET) access code.
3. Designate your desired time by...

NEAX2400 IMX Feature Programming Manual
Page 734ND-70184 (E), Issue 3
T-62 Timed Reminder
Programming
STEP 1:ASYD - System Data 1, Index 162, bits 6 and 7 tone type when a Timed Reminder call is answered.
b7
b6b7b6
0 0 = Music-On-Hold 0 1 = Announcement
Note:
When Music-On-Hold is selected, STEPs 5 through 8 are not required.
System Data 1, Index 163, bit 7. Start time for Timed Reminder/Wake Up Call 0/1 = On time / 5min.
earlier the appointed time.
System Data 1, Index 169, bits 4. through 7. Maximum...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 735
Tone Block T-63
T-63 Tone Block
General Description
This feature allows the user of a station (via analog adapter) or an analog station (PB) to restrict any call. This
prevents interruption of data transmission, before the connection.
Operating Procedure
To set the service: 
1. Lift the handset: receive the dial tone.
2. Dial the access code of “Data Privacy on Demand; Entry”.
3. Hear the special dial tone or the dial tone (depending...

NEAX2400 IMX Feature Programming Manual
Page 736ND-70184 (E), Issue 3
T-63 Tone Block
Programming
STEP 1:ANPD - Reserve a number level for feature access and cancel. Assign for Normal, (N) and Hooking
(H). Assign NND in accordance with a predetermined numbering plan.
STEP 2:ASPA - Assign the access code for Tone Block as shown below:
CI = H, SRV=SSCA, SIDA=48 (Data Privacy on Demand; Entry)
CI = H, SRV=SSCA, SIDA=49 (Data Privacy on Demand; Cancel)
CI = N, SRV=SSCA, SIDA=48 (Data Privacy on Demand;...