NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 687
Slumber Time - Do Not Disturb S-106
Programming (cont’d)
TN = [x] Tenant Number
STN = [x] Station Number
G = [x] Slumber Time Group Number (1-7) 
Assignment of Slumber Time Data 
ASLU2 - 
G = [x] Slumber Time Group Number (1-7) 
CNT = [x] Count of Assigned Transfer Destination/Time Data
TFR 1/2: Transfer to attendant/announcement machine 
FROM = [x]
 Time Data
TO = [x] (For assigning one day assign as 00:00).
STEP 6:ASFC - Allow...

NEAX2400 IMX Feature Programming Manual
Page 688ND-70184 (E), Issue 3
S-127 Serial Call - Dterm
S-127  Serial Call - Dterm
General Description
This feature allows the Dterm user to set SERIAL CALL to the central office line/tie line call and extend the call to
the desired station/trunk. When the communication with the desired party ends, the announcement instructing the
caller to dial the next desired party number is sent out. The caller, by following the instructions, can be connected
to a number of...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 689
Serial Call - DtermS-127
Service Conditions (cont’d)
10. Whether to send the announcement can be determined on a system basis. If the announcement is not sent,
the caller receives dial tone. Both the first and the second announcement is connected in single connection,
and the caller receives no tone until the announcement is sent.
11. When Serial Call is attempted, and the caller encounters all announcement trunks busy or when there...

NEAX2400 IMX Feature Programming Manual
Page 690ND-70184 (E), Issue 3
S-127 Serial Call - Dterm
Service Conditions (cont’d)
 when the access code is dialed for trunk call origination, and inter digit timer expires before the
call originating route is determined, resulting in restriction.
 when the outgoing trunks are all busy (if Tandem Trunk Queuing service is set, the service is
activated).
20. After the second announcement is sent out, whether to allow dialing of the next number or to release the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 691
SMDR Output Expansion - ANI/CPN S-129
S-129  SMDR Output Expansion - ANI/CPN
General Description
This feature expands SMDR information output, by which calling numbers from Central Office may be output to
the expanded area.
Operating Procedure
No manual operation is required.
Service Conditions
1. When the expanded area information is used, SMDR equipment must corresponds to the expanded output
format.
2. Users may assign 24 kinds of...

NEAX2400 IMX Feature Programming Manual
Page 692ND-70184 (E), Issue 3
S-129 SMDR Output Expansion - ANI/CPN
Service Conditions (cont’d)
Note:
Meanings of ANI information identifier numbers:
0 = Not output
1 = Display
2 = Not display
3 = Not provide service
4 = Outgoing C.O. call
5 = Service Condition
5. When an office receiving a calling number from Central Office extends the call to another office through
CCIS and charging is performed at the extended office, the maximum calling number is 16 digits....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 693
SMDR Output Expansion - ANI/CPN S-129
Programming (cont’d)
When Calling Number is output to SMDR, the following expanded format is used:
System Data 1, Index 288, Bit 5. Expanded SMDR Output for SMDR A Apparatus. 0/1 = Out/In
Service.
System Data 1, Index 290, Bit 5. Expanded SMDR Output for SMDR B Apparatus. 0/1 = Out/In
Service.
System Data 1, Index 292, Bit 5. Expanded SMDR Output for SMDR C Apparatus. 0/1 = Out/In
Service.
System...

NEAX2400 IMX Feature Programming Manual
Page 694ND-70184 (E), Issue 3
S-129 SMDR Output Expansion - ANI/CPN
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
 (Note)
STEP 1:ASYDL - System Data 1, Index 241, Bit 6. 0/1 = When the length of...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 695
Tandem Switching of TIE Trunks - 2/4-Wire T-1
T-1  Tandem Switching of TIE Trunks - 2/4-Wire
General Description
This feature allows trunk-to-trunk connections through the switching system, without the need for any Attendant
assistance or control. The major use of this feature is in association with the Dial Tandem TIE Line Network to allow
TIE Line connections and incoming TIE Line calls automatic access to, and completion of, local...

NEAX2400 IMX Feature Programming Manual
Page 696ND-70184 (E), Issue 3
T-1 Tandem Switching of TIE Trunks - 2/4-Wire
Interactions (cont’d)
f.) CCSA trunk
4. STATION MESSAGE DETAIL RECORDING (SMDR) [S-10]: On Tandem Connections, the incoming
TIE Trunk group route number and outgoing trunk number are recorded.
5. Two outgoing trunk group restriction tables are provided per system. The Direct Dial Access table is
indexed when a distant user dials the trunk group access code, and the ATTENDANT CONSOLE [A-3]...