NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 657
Speed Calling - Station S-21
S-21 Speed Calling - Station
General Description
This feature allows a user to dial certain frequently-called exchange network numbers using fewer digits
(abbreviated call codes) than normally required. Using this feature, a user can establish his own abbreviated codes. 
Operating Procedure
1. Lift handset or press SPEAKER key; receive dial tone.
2. Dial SPEED CALLING; enter access code (one to three...

NEAX2400 IMX Feature Programming Manual
Page 658ND-70184 (E), Issue 3
S-21 Speed Calling - Station
Service Conditions (cont’d)
11. A pause may be programmed, using the “*” key of a PB pad. This will take one of the 24 digits available.
Rotary type phones cannot store a pause. A pause lasts 2.8 seconds.
12. It is not necessary to erase a stored number in order to store another number. The second number replaces
the first.
13. When a caller places a call via Outgoing Call Alternative (OGCA), and when the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 659
Speed Calling - Station S-21
Programming (cont’d)
STEP 5:AISA - Program the tenant, station, type of station, and the number of SPEED CALLING blocks to be
assigned to the Primary station. 
TN: Tenant Number 
STN: Station Number 
MST/SLV: Primary/Secondary 
M: Primary Station
S: Secondary Station 
BLOCK: Number of Blocks 
STN: When assigning Secondary Station, assign the Primary Station number.
STEP 6:AKYD - Type:Function:SPEED...

NEAX2400 IMX Feature Programming Manual
Page 660ND-70184 (E), Issue 3
S-23 Speed Calling - Group
S-23  Speed Calling - Group
General Description
This feature allows a user to share a set of common Speed Calling numbers with other users in the group.
Operating Procedure
To record: 
1. Lift handset or press SPEAKER key; receive dial tone.
2. Dial the SPEED CALLING access code (one to three digits).
3. Dial the abbreviated call code (one to three digits) and the called exchange network numbers; receive...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 661
Speed Calling - Group S-23
Service Conditions (cont’d)
10. SPEED CALLING-GROUP and SPEED CALLING-STATION [S-21] use the same block of memory
tables. 
11. SPEED CALLING-GROUP data remains, even if the system is re-initialized or there is a power failure.
12. A pause may be programmed using the “
*” button of a PB pad. This will take one of the 24 digits
available. Rotary type phones cannot store a pause. A pause lasts 2.8 seconds.
13....

NEAX2400 IMX Feature Programming Manual
Page 662ND-70184 (E), Issue 3
S-23 Speed Calling - Group
Programming (cont’d)
STEP 4:ASFC - Assign a Service Feature Class that allows SFI 19 to the stations to receive SPEED
CALLING-STATION.
STEP 5:AISA - Program the tenant, station, type of station, and the number of Speed Calling blocks to be
assigned to the Primary station. 
TN: Tenant Number 
STN: Station Number 
MST/SLV: Primary/Secondary 
M: Primary Station
S: Secondary Station 
BLOCK: Number of Blocks 
STN:...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 663
Save And Repeat - DtermS-24D
S-24D Save And Repeat - Dterm
General Description
This feature allows for a Dterm set to save a specific dialed number and then redial that number later.
Operating Procedure
1. Go off-hook, seize any idle line, and dial a number.
2. When the number has been dialed, press the SAVE AND REPEAT (S&R) feature key. The dialed number
is stored for future use. The associated LED lights. The LCD displays:
Note:...

NEAX2400 IMX Feature Programming Manual
Page 664ND-70184 (E), Issue 3
S-24D Save And Repeat - Dterm
Interactions
AKYD is assigned after ASDT is assigned. Assign a LEN as TEC 12.
Programming
STEP 1:AKYD - Assign the Dterm according to the following parameters:
TN: 1
STN: Station Number 
TP: Type of D
term 0/1:
RING:
0: No Ringing 
1: Ringing All Lines 
2: Ringing on Prime Line Only
3: Flexible Ring Assignment, enables RG parameter. 
KYN: Key Number (1-40)
KYI: Service Index
0: Key Not Used
1: Feature Key...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 665
Service Display - DtermS-25D
S-25D  Service Display - Dterm
General Description
This feature generates LCD displays corresponding to the various features as they are initiated.
Operating Procedure
Each display is automatically generated when a feature is initiated. 
Service Conditions 
1. Each display is controlled by System Data and is produced accordingly. The service display may be
allowed or denied in System Data on a per-system...

NEAX2400 IMX Feature Programming Manual
Page 666ND-70184 (E), Issue 3
S-26D Speed Calling - One Touch - Dterm
S-26D  Speed Calling - One Touch - Dterm
General Description
This feature allows Dterm users to dial telephone numbers by pressing a single key. Up to 12/24 numbers may be
programmed by the Dterm user. 
Operating Procedure
To program: 
1. Press the FEATURE key.
2. Press the SPEED CALLING-ONE TOUCH button. 
3. Dial the desired number.
4. Press the FEATURE key again.
5. Display will show SPEED...