NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 607
Special Dial Tone S-2
S-2  Special Dial Tone
General Description
This feature provides a distinctive dial tone to a user after the switch hook has been pressed, enabling the user to
activate a specific service feature.
Operating Procedure
1. While connected with the first party, user presses the switch hook; receives SPECIAL DIAL TONE.
2. User may activate a service feature, such as: 
CALL HOLD [C-6] 
CALL TRANSFER-ALL CALLS [C-11]...

NEAX2400 IMX Feature Programming Manual
Page 608ND-70184 (E), Issue 3
S-3 Speed Calling - System
S-3 Speed Calling - System
General Description
This feature allows a user or ATTENDANT CONSOLE [A-3] to call frequently dialed numbers using fewer digits
(abbreviated call codes) than would normally be required.
Operating Procedure
1. Lift handset; receive dial tone,
2. Dial SPEED CALLING - SYSTEM access code (maximum three digits), or press D
term Speed Calling
key.
3. Dial abbreviated call code (maximum...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 609
Speed Calling - System S-3
Programming
STEP 1:ASYD - System Data 2, Index 1, bit 7. Does TOLL RESTRICTION [T-7] apply to SPEED
CALLING-SYSTEM? 0/1: No/Yes. 
STEP 2:ANPD - Reserve a number level for feature access. Assign Connection Indexes of Normal (N),
Hooking (H), and Busy (B). Assign NND in accordance with a predetermined numbering plan.
STEP 3:ASPA - Assigning an access code to SPEED CALLING-SYSTEM, assign SRV = SSC (Service...

NEAX2400 IMX Feature Programming Manual
Page 610ND-70184 (E), Issue 3
S-3D Speed Calling - System - Dterm
S-3D  Speed Calling - System - Dterm
General Description
This feature allows a Dterm user to call frequently dialed numbers using fewer digits (abbreviated call codes) than
would normally be required.
Operating Procedure
Originating a call from a Dterm:
1. Press the SPEED CALLING-SYSTEM (SPEED-SYS) key. 
2. Dial the abbreviated call code (maximum of four digits). The LCD displays:
3. The call is...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 611
Speed Calling - System - DtermS-3D
Programming
STEP 1:ASYD - System Data 2, Index 1, bit 7. Does TOLL RESTRICTION [T-7] apply to SPEED
CALLING-SYSTEM? 0/1: No/Yes. 
STEP 2:ANPD - Reserve a number level for feature access. Assign Connection Indexes of Normal (N),
Hooking (H), and Busy (B). Assign NND in accordance with a predetermined numbering plan.
STEP 3:ASPA - Assigning an access code to SPEED CALLING-SYSTEM, assign SRV = SSC...

NEAX2400 IMX Feature Programming Manual
Page 612ND-70184 (E), Issue 3
S-4 Splitting
S-4 Splitting
General Description
This feature allows the ATTENDANT CONSOLE [A-3] to speak privately with one party on an Attendant-handled
connection without the other party overhearing.
Operating Procedure
To speak with the called party only:
1. Dial the desired telephone number.
2. Station class/telephone number is displayed.
3. Wait for the party to answer.
To speak with the calling party only: 
1. Press the SRC key....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 613
Splitting - DtermS-4D
S-4D  Splitting - Dterm
General Description
This feature allows a Dterm user to alternately converse between two separate parties while one party is connected
and one party remains on hold. The user uses the TRANSFER button to alternate conversations between the two
parties.
Operating Procedure
While a conversation is in progress:
1. Press the TRANSFER key; hear special dial tone. 
2. Dial the new number; the...

NEAX2400 IMX Feature Programming Manual
Page 614ND-70184 (E), Issue 3
S-6 Station-Controlled Conference
S-6 Station-Controlled Conference
General Description
This feature allows any NEAX2400 IMX station to establish a conference. The conference may be any combination
of stations and/or trunks (inside and outside parties).
Operating Procedure
Procedure 1 (MEET-ME CONFERENCE):
1. User wishing to establish the conference (conference leader) calls each party desired and advises them of
the conference.
2. All...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 615
Station-Controlled Conference S-6
Programming
STEP 1:ANPD - A number level must be reserved for station numbering plan. In an existing system, a station
level will already be established. If a vacant level does exist, it may be used to create 2 or 3-digit
station numbering. For example:
TN: 1 DC: 3 CI: N, H, BNND: 1 BLF: 1-On
STEP 2:ASPA - For the desired station numbering assign SRV = STN (Station). For example: 
ACC: 3 CI: N, H, B...

NEAX2400 IMX Feature Programming Manual
Page 616ND-70184 (E), Issue 3
S-7 Station Hunting - Circular
S-7 Station Hunting - Circular
General Description
This feature permits a call to be processed automatically through a hunt group of busy extensions, in a programmed
order.
Operating Procedure
No manual operation is required.
Service Conditions 
1. This feature can be activated via FCCS.
2. When all stations within a Circular Hunt Group are busy:
a.) If a call is terminated to a group does not have a...