NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 597
Radio Paging R-16
Programming (cont’d)
If the paged party doesn’t respond by the same period of time after the second page, the page is
cancelled. 
System Data 1, Index 244, bit 0. Answer by Radio Paging answer code. 0/1: Out/In Service. Note that
this bit is valid when System Data 1, Index 73, bit 4 is 1 (Station Number/Individual ATT Number is
automatically sent).
STEP 2:ARTD - Assign the Radio Paging route as shown below:
RT:  1...

NEAX2400 IMX Feature Programming Manual
Page 598ND-70184 (E), Issue 3
R-27 Route Restriction - Announcement
R-27  Route Restriction - Announcement
General Description
This feature permits a station-originated call, dialed to a restricted outgoing number, to be automatically routed to a
recorded announcement informing the caller that the dialed number is restricted. (TOLL RESTRICTION [T-7])
Operating Procedure
No manual operation is required after this feature has been programmed in System Data.
Service...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 599
RS-464A PAD R-37
R-37 RS-464A PAD
General Description
This service is for changing the current PAD control system for the lines and external trunks to a PAD control system
which conforms to the RS-464A specification.
The following table outlines the comparison between the current PAD control and the RS-464A PAD control. 
Note:
ONS: Line interface to On-Premises Line (General Telephone)
OPS: Line interface to Off-Premises Line (Log...

NEAX2400 IMX Feature Programming Manual
Page 600ND-70184 (E), Issue 3
R-37 RS-464A PAD
General Description (cont’d)
PAD PATTERN 2 PAD PATTERN 2 PAD PATTERN 2
24 DTR with SFI 50 = 0 24 DTR with SFI 50 = 1 24DTR with APAD Setting
ARTD 
PA D  
SettingTr a n s m i t  
PA DReceive 
PA DARTD 
PA D  2Transmit 
PA DReceive 
PA DAPAD 
SettingTr a n s m i t  
PA DReceive 
PA D
0-9db-3db 0ARTD, 
PA DARTD, 
PA D1 -3db +3db
1 -3db +3db 1 -3db +3db 2 -3db -3db
2 -3db -3db 2 -3db -3db 3 -6db 0db
3 -6db 0db 3 -6db 0db 4...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 601
RS-464A PAD R-37
General Description (cont’d)
In 4 Wire E+M Mode, the 8TLTR can set PAD values using switch settings and ARTD and APAD values. 
In the following table, P0 and P1 are assigned by setting ARTD to a value of 0, CDN 30:PAD and setting values by
using Switch 1 (P0) and Switch 2 (P1). P2 and P3 are assigned by setting ARTD/APAD to a value of 5, and PAD
values are set by using Switch 3 positions 1, 2, 3 and 4 (P2) and...

NEAX2400 IMX Feature Programming Manual
Page 602ND-70184 (E), Issue 3
R-37 RS-464A PAD
Service Conditions (cont’d)
3. An Attendant Console is regarded as an ONS. The Attendant Console will follow the PAD values assigned
in ARTD.
4. If PAD data is assigned by APAD command, this data overrides other PAD data assigned by ARTD,
except when switch settings on the 24DTR are set to ARTD fixed.
5. PAD settings for the 8TLTR can be set using ARTD/APAD or a combination of switch settings and
ARTD/APAD.
6. This...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 603
Ringer Mute R-49
R-49 Ringer Mute
General Description
This feature allows a user to stop ringing by pressing the associated feature key on the Dterm.
Operating Procedure
1. The Dterm user presses the RINGER MUTE key; the ringing is muted and the LED of the key lights. RING
OFF is displayed for three seconds.
2. The D
term user presses the RINGER MUTE key again; the ringing is recovered and the LED of the key is
turned off. RING ON is...

NEAX2400 IMX Feature Programming Manual
Page 604ND-70184 (E), Issue 3
R-51 Route Name Display
R-51  Route Name Display
General Description
This feature allows a user to assign a desired trunk type for a route by the system data. The assigned trunk type
(maximum of 4 or 8 digits) is displayed on the upper line of Dterm LCD.
 4-digit display
TK No.
 8-digit display
Note:
Trunk type, which can be changed by system data.
Operating Procedure
No manual operation is required.
Service Conditions
1. Trunk types...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 605
Route Name Display R-51
Service Conditions (cont’d)
 8-digit display
8. This feature is available when the D
term user presses the call terminating sub line. This feature is also
available when the user presses the held sub line after holding a call using the HOLD key.
9. For data assignment to each of NDM (Network Data Memory) and LDM (Local Data Memory), different
commands can be used. However, the data in NDM has a priority. The...

NEAX2400 IMX Feature Programming Manual
Page 606ND-70184 (E), Issue 3
S-1 Single-Digit Station Calling
S-1 Single-Digit Station Calling
General Description
This feature allows the assignment of single digits for station numbers.
Operating Procedure
1. Lift the handset; receive dial tone.
2. Dial the Single-digit (preprogrammed) telephone number.
3. The desired service station will be rung. 
Service Conditions
1. The single-digit number must be different from the first digit of trunk access codes, service...