NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 617
Station Hunting - Circular S-7
Service Conditions (cont’d)
16. This feature will be activated whenever the hunt group is dialed or terminated under the following
conditions:
a.) dialed from a station
b.) dialed from ATTENDANT CONSOLE [A-3]
c.) dialed from DID [D-8]
d.) dialed from TIE LINE [T-3]
e.) terminated by DIT [D-7]
f.) terminated by HOT LINE [H-1]
g.) terminated by OFF-HOOK ALARM [O-6]
h.) terminated by PRIORITY CALL [P-9]
17....

NEAX2400 IMX Feature Programming Manual
Page 618ND-70184 (E), Issue 3
S-7 Station Hunting - Circular
Service Conditions (cont’d)
22. The incoming call terminated through FCCS link to the Station Hunt group, which is programmed by the
Physical Station Number, is not hunted. 
23. When a Physical Station Number and telephone number assigned to a Circular Hunt station are identical,
priority is attached to STATION HUNTING - CIRCULAR via FCCS.
24. When using this feature within an FCCS network, when CALL...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 619
Station Hunting - Circular S-7
Service Conditions (cont’d)
32. The following are the conditions when STATION HUNTING - CIRCULAR is programmed on LDM.
a.) When a call is directly placed to a Circular Hunt station, CALL FORWARDING - ALL CALLS
[C-5] is normally activated (the call is forwarded to the designated station).
b.) When a call to a Circular Hunt Station is forwarded by CALL FORWARDING - BUSY LINE
[C-2] and the forwarded party...

NEAX2400 IMX Feature Programming Manual
Page 620ND-70184 (E), Issue 3
S-7 Station Hunting - Circular
Interactions (cont’d)
b.) A direct call to Station A will respond to CALL FORWARDING-BUSY LINE [C-2].
c.) A call to the Station Hunting-Circular group will bypass Station A, if that station is both busy and
has set CALL FORWARDING-BUSY LINE [C-2]. The next station in the group will ring.
d.) A call forwarding-override call from Station B to Station A will hunt if Station A is busy.
5. STATION MESSAGE...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 621
Station Hunting - Circular S-7
Programming
STEP 1:ASHC - Assign the required data for the STATION HUNTING-CIRCULAR Group. 
TN: Tenant Number 
STN: Station Number 
SECRET: Indication of Secretary Station 0/1-/Assignment 
SECRET STN: Station Number of the Secretary/Station 
*STN: Station numbers of the stations included in the group.
STEP 2:APHN - Assign Phantom Number (PHSTN) to each Circular Hunt Station (as necessary)
TN: Tenant...

NEAX2400 IMX Feature Programming Manual
Page 622ND-70184 (E), Issue 3
S-7 Station Hunting - Circular
FCCS Programming (cont’d)
STEP 2:ASHCN - This data must be assigned to the NCN.
Assign the Circular Hunt Group using Telephone Number.
UGN: User Group Number 
TELN: Telephone Number in the Circular Hunt Group
First TELN: First assigned Telephone Number
SECRETARY TELN:Secretary Telephone Number
STEP 3:APHNN - Assign Phantom Telephone Number (PHTELN) to each Circular Hunt Station
UGN: User Group Number...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 623
Station Hunting - Secretarial S-8
S-8  Station Hunting - Secretarial
General Description
This feature allows calls to a Hunt group to forward to a secretarial station when all the stations in the group are busy.
Operating Procedure
No manual operation is required.
Service Conditions 
1. When all stations within a Hunt group are busy, the incoming call is routed to the station programmed as
the Secretarial Station. 
2. If the...

NEAX2400 IMX Feature Programming Manual
Page 624ND-70184 (E), Issue 3
S-8 Station Hunting - Secretarial
Programming
See STATION HUNTING-CIRCULAR [S-7] and STATION HUNTING-TERMINAL [S-9]. These
two types of station hunting use secretaries.
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 625
Station Hunting - Terminal S-9
S-9  Station Hunting - Terminal
General Description
This feature enables calls placed to busy stations, other than Pilot stations of a Hunt group, to receive a busy tone
rather than proceed through the normal hunting process. However, if the call is placed to the busy Pilot station of a
Hunt group, station hunting will proceed as usual.
Operating Procedure
No manual operation is required.
Service...

NEAX2400 IMX Feature Programming Manual
Page 626ND-70184 (E), Issue 3
S-9 Station Hunting - Terminal
Service Conditions (cont’d)
d.) A station can belong to one hunting group only; it cannot belong to another group including that
for STATION HUNTING - CIRCULAR [S-7] or UNIFORM CALL DISTRIBUTION (UCD)
[U-1].
e.) When all stations to be hunted are busy, the incoming call is forwarded finally to the Secretarial
Station. However, when the station is not assigned or is also busy, busy tone is provided to the...