NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 637
Station Message Detail Recording (SMDR) S-10
Service Conditions (cont’d)
Example 3
 Node A tries to collect the billing information of Node B via FCCS, using the polling method (Node A
cannot collect the billing information of Node B via FCCS).
 Node B sends the billing information via CCIS, ignoring polling from Node A.
 Node B deletes the Point Code (CCIS) of Node C for centralized billing data when required to send billing...

NEAX2400 IMX Feature Programming Manual
Page 638ND-70184 (E), Issue 3
S-10 Station Message Detail Recording (SMDR)
Service Conditions (cont’d)
Example 4
 Node A collects the billing information of Node B and Node C via FCCS, using the polling method.
 Node A sends the billing information of Node A, Node B and Node C.
Node C
CCIS - Center Node
non IMX
SMDR 
EquipmentFCCS Network
IMX
36456
55213
25454
75213
Billing information of 
Nodes A, B, C
Node D
IMX CCIS
79
87
9
8
46
51
38
92
5
4
65
65
Node C...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 639
Station Message Detail Recording (SMDR) S-10
Service Conditions (cont’d)
Example 5
 Node A collects the billing information of Node B and Node C via FCCS, using the polling method (Billing
information of Node B cannot be collected).
 Node B sends the billing information to Node D via CCIS, ignoring polling from Node A.
 Node B deletes the Point Code (CCIS) for Node D when Node B wants to send billing information for
polling from...

NEAX2400 IMX Feature Programming Manual
Page 640ND-70184 (E), Issue 3
S-10 Station Message Detail Recording (SMDR)
Service Conditions (cont’d)
Example 6
 Node A collects the billing information of Node B, Node C and Node D, which are stored in Node B by
polling method.
 Node D sends the billing information to Node B.
 SOCKET Interface (LAN Interface) Conditions:
42. SMDR data can be output via LAN cable.
43. A maximum of four SMDR apparatuses per node are available.
44. When providing this feature...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 641
Station Message Detail Recording (SMDR) S-10
Interactions (cont’d)
5. LEAST-COST ROUTING-3/6-DIGIT [L-5]: SMDR will record the digits sent rather than the digits
dialed.
6. The destination station is recorded on SMDR for the following features:
CALL FORWARDING [C-2, 3, 5]
CALL PICKUP [C-7, 30]
7. CALL FORWARDING-INTERCEPT [C-25]: An incoming trunk call responds to Call Forwarding-
Intercept to the Attendant Console. SMDR records the...

NEAX2400 IMX Feature Programming Manual
Page 642ND-70184 (E), Issue 3
S-10 Station Message Detail Recording (SMDR)
Programming (cont’d)
SMDR output port will be designated. For this designation, the attributes of the terminal that outputs
the detail call information should have been designated by indexes 117-123. (Assigned by the AIOC
command.) 
Also for detecting a fault of the SMDR, set the SMDR fault detect timer.
Index 288 = Charging information port of SMDR A.
Bit 4: IOC Equipment Number...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 643
Station Message Detail Recording (SMDR) S-10
Programming (cont’d)
System Data 1, Index 582, Bit 0-3. Assign the number of nodes to be polled at once.
0000 = 1 0001 = 1 0010 = 2 0011 = 3 0100 = 4 0101 = 5
0110 = 6 0111 = 7 1000 = 8 1111 = 8 
(Note 2)
Note 1:
This data is valid when the data is assigned at SYS1, Index 512.
Note 2:
For the numbers more than 8, assign the data value as 8.
System Data 1, Index 583, Bit 0-2. The timing for...

NEAX2400 IMX Feature Programming Manual
Page 644ND-70184 (E), Issue 3
S-10 Station Message Detail Recording (SMDR)
Programming (cont’d)
After the Center Node (multiple CN: possible on a network) is assigned for centralized billing-Fusion,
let the Center Node recognize its polling destination (specified by the FPC), referring to the table
below. In the table, each bit represents Fusion Point Code ranging from 1 to 253. When “1” is set, the
FPC is specified as the polling destination....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 645
Station Message Detail Recording (SMDR) S-10
Programming (cont’d)
System Data 1, Index 641, Bit 0. Type of the station number for the ICS text format.
0/1=Physical Station Number/Telephone Number.
System Data 1, Index 641, Bit 3. Kind of the route number for the ICS text format.
0/1=Physical Route Number/Logical Route Number.
STEP 3:SOCKET Interface (Lan Interface) Programming
System Data 1, Index 529: Assign the methods of parity...

NEAX2400 IMX Feature Programming Manual
Page 646ND-70184 (E), Issue 3
S-10 Station Message Detail Recording (SMDR)
Programming (cont’d)
STEP 7:ASFC - Assign data “1” to SFI14 of a Service Feature Class, the traffic of which is to be registered on
SMDR (Trunk Basis). Assign data “1” to SFI58 of a Service Feature Class the traffic of which is to be
registered on SMDR (STN to STN Basis).
Note:
When SMDR for station-to-station calling is not used, both stations in communication must be restricted at the...