NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 677
Serial Call - Loop Release S-64
FCCS Programming 
No unique programming is required for the FCCS network. 

NEAX2400 IMX Feature Programming Manual
Page 678ND-70184 (E), Issue 3
S-99 Split Call Forwarding
S-99 Split Call Forwarding
General Description
This feature allows a station to set two different target stations for CALL FORWARDING-ALL CALLS
(FORWARD)/BUSY LINE (FORWARD-BY)/DON’T ANSWER (FORWARD-DA), depending on whether the
incoming call is from an internal station or an outside party (C.O. TIE, DID, etc.). 
Operating Procedure
1. Station A sets or is set for CALL FORWARDING-ALL CALLS/BUSY LINE/DON’T...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 679
Split Call Forwarding S-99
Operating Procedure (cont’d)
To set SPLIT CALL FORWARDING using Dterm feature key:
To set Call Forwarding from an individual station (Dterm): 
1. Setting Call Forwarding for an incoming call from a station:
a.) Confirm that the PAGE* (One-touch changeover) lamp is on; if the lamp is off, turn the lamp on
by pressing the PAGE key. 
b.) Lift the handset or press the SPEAKER key; receive dial tone. 
c.) Press...

NEAX2400 IMX Feature Programming Manual
Page 680ND-70184 (E), Issue 3
S-99 Split Call Forwarding
Operating Procedure (cont’d)
When the destination is an outside trunk, the Dterm displays:
To cancel Call Forwarding from an individual station (Dterm):
1. Cancelling Call Forwarding for an incoming call from a station: 
a.) Confirm that the PAGE (One-Touch Changeover) lamp is on; if the lamp is off, turn the lamp on
by pressing the PAGE key. 
b.) Lift the handset or press the SPEAKER key; receive service set...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 681
Split Call Forwarding S-99
Operating Procedure (cont’d)
When the destination is an ATTENDANT CONSOLE, the Dterm displays:
When the destination is an outside trunk, the D
term displays:
2. To monitor the assigned data for station-to-station calls:
a.) Confirm that the PAGE key LED on the D
term is illuminated. (If it is not illuminated, press the
PAGE key to turn it on.)
b.) While the D
term is in the idle state (on-hook), press the...

NEAX2400 IMX Feature Programming Manual
Page 682ND-70184 (E), Issue 3
S-99 Split Call Forwarding
Operating Procedure (cont’d)
b.) Dial the Tenant Number (2 digits) of the originating station and the originating telephone number.
c.) Press the RELEASE key; receive service set tone.
2. Cancelling Call Forwarding for an incoming call from an outside party:
a.) Press an idle loop key and dial the FORWARD, FORWARD-BY, or FORWARD-DA access
code for an incoming call from an outside party; receive special dial...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 683
Split Call Forwarding S-99
Service Conditions (cont’d)
11. If SPLIT CALL FORWARDING is set on a station in the hunting group (STATION HUNTING -
CIRCULAR [C-7], - TERMINAL [S-9], that station is skipped in hunting. However, if the station has set
SPLIT CALL FORWARDING for station-to-station calls only, the station is hunted for incoming calls
from outside. If the station has set SPLIT CALL FORWARDING for outside calls only, the station...

NEAX2400 IMX Feature Programming Manual
Page 684ND-70184 (E), Issue 3
S-99 Split Call Forwarding
Programming (cont’d)
SN=1, FKY=55: Call Forwarding - One - Touch Changeover (PAGE)
This command is used for assigning a function to each soft key.
STEP 6:ASFC - Allows Call Forwarding-All Calls (SFI = 7), Call Forwarding-Busy Line (SFI = 9), or Call
Forwarding-Don’t Answer (SFI = 8) to the SFC of the Station.
STEP 7:ARTD - Assign route data to the route of the trunks which validates C.F.-All Calls, C.F.-Busy...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 685
Slumber Time - Do Not Disturb S-106
S-106  Slumber Time - Do Not Disturb
General Description
This service allows a slumber time for up to four times per day on a Station group basis. During the slumber time,
all stations in the group concerned are placed into Do Not Disturb mode, and incoming calls (Station/DID/DIT) will
be routed to the Attendant or an announcement machine.
Operating Procedure
No manual operation is required.
Service...

NEAX2400 IMX Feature Programming Manual
Page 686ND-70184 (E), Issue 3
S-106 Slumber Time - Do Not Disturb
Service Conditions (cont’d)
STATION HUNTING [S-7, 9]
UNIFORM CALL DISTRIBUTION [U-1]
17. CALL BACK [C-1] and CALL WAITING-ORIGINATING [C-31] can be set from a Slumber Time
station.
18. Each of the following services is restricted to a Slumber Time station:
CALL WAITING-ORIGINATING [C-31] 
CALL BACK [C-1] 
EXECUTIVE RIGHT-OF-WAY [E-1] 
19. Each of the following terminals can access to a Slumber Time...