NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 717
Trunk Answer from Any Station (TAS) T-8
T-8  Trunk Answer from Any Station (TAS)
General Description
This feature allows any station (except one with incoming restrictions) to answer incoming calls when the system is
in Night Mode. Incoming exchange network calls will activate a common alert (TAS) signal at the customer’s
premises. By dialing a specified code, any station may answer the call and then extend it to any other station...

NEAX2400 IMX Feature Programming Manual
Page 718ND-70184 (E), Issue 3
T-8 Trunk Answer from Any Station (TAS)
Interactions (cont’d)
4. CALL TRANSFER-ALL CALLS [C-11]: A station answering a call via the TAS feature will have access
to the transfer feature. 
5. CENTRALIZED ATTENDANT SERVICE (CAS) [C-20]: TAS may be installed at either the Main site
only or at both the Main and Satellite sites. Operations at either site are the same as TAS installed in a non-
CAS system. The Satellite system must have a...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 719
Trunk Answer from Any Station (TAS) T-8
Programming (cont’d)
STEP 5:ACFR - Allow a Transfer Service Feature Index of 5, TAS to the listed types of incoming calls to be
answered by TAS. The Call Class Indexes (CCI) will correspond to ARTD, CDN 6:TCL; Trunk Class
parameter.
CCI: 1-LDN
2-DDD2
3-DDD3
4-TIE LINE 
5-DDD4
STEP 6:ATA S - Assign the TAS circuit to the TN, MG, PIM, and the circuit number: 0/1; based on the circuit
location. TAS...

NEAX2400 IMX Feature Programming Manual
Page 720ND-70184 (E), Issue 3
T-9 Trunk Group Busy Lamp
T-9 Trunk Group Busy Lamp
General Description
This feature provides the ATTENDANT CONSOLE [A-3] with a visual indication when all trunks in a particular
trunk group are busy (LDN, WATS, FX, DOD, CCSA, TIE or Special Trunks). Assignment of the TGBLs is made
using the MAINTENANCE ADMINISTRATION TERMINAL (MAT) [M-18].
Operating Procedure
No manual operation is required.
Service Conditions
1. The ATTENDANT CONSOLE...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 721
Trunk Group Busy Lamp T-9
FCCS Programming 
Programming for the IMX-U
(Series 7400 software enhancement) TGBL data can be transmitted to all the local nodes by the
circuit card DLMX (PA-PC94) via DLKC circuit cards in the IMX-U. For more detailed information,
see the NEAX2400 IMX Office Data Specification and the NEAX2400 IMX Circuit Card Manual.
Programming for the DLMX (PA-PC94) Circuit Card
STEP 1:ASYD - SYS1 INDEX 15, b0-3: Number...

NEAX2400 IMX Feature Programming Manual
Page 722ND-70184 (E), Issue 3
T-10 Trunk-to-Trunk Connection
T-10 Trunk-to-Trunk Connection
General Description
This feature provides any user with the ability to conference together either two Central Office calls or a Central
Office and TIE Line call.
Operating Procedure
1. Place incoming caller on hold.
2. Receive special dial tone.
3. Dial the desired Central Office or TIE access code. 
4. Receive second dial tone.
5. Dial the desired number; receive answer.
6....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 723
Trunk-to-Trunk Connection T-10
Programming (cont’d)
System Data 2, Index 1, Bits 0 & 1. CONSULTATION HOLD. Assign data “11” for
CONSULTATION HOLD service on Originating, Terminating, and Tandem calls.
System Data 2, Index 6, Bit 2. This Bit remains as data “0”. CALL TRANSFER-ALL CALLS [C-11].
System Data 2, Index 6, Bit 3. Enable add-on station. This Bit remains as data “0” for THREE-WAY
CALLING [T-2]. 
System Data 3, Index 2. Assign...

NEAX2400 IMX Feature Programming Manual
Page 724ND-70184 (E), Issue 3
T-10 Trunk-to-Trunk Connection
FCCS Programming (cont’d)
STEP 2:ARRCN - Routes that will be allowed TRUNK-TO-TRUNK CONNECTION must be allowed here
for ARI-A-RES.
ICRT: Incoming Route Number 
OGRT: Outgoing Route Number
ARI-A-RES: This allows/restricts trunk-to-trunk (tandem) connection via the Attendant Console
and stations. 
ARI-D-RES: This allows/restricts trunk-to-trunk (tandem) connections via Direct Dial access from
a station and...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 725
Tenant Service T-12
T-12 Tenant Service
General Description
This feature provides for more than one organization (tenant) to share the same PBX. Through system programming,
each organization may be restricted to its own Central Office trunks, ATTENDANT CONSOLEs [A-3], and
extension links. In addition, incoming calls are directed to the specific organization (tenant). 
Operating Procedure
No manual operation is required.
Service...

NEAX2400 IMX Feature Programming Manual
Page 726ND-70184 (E), Issue 3
T-12 Tenant Service
Interactions (cont’d)
5. CALL FORWARDING [C-2, 3, 5]: When a station call forwards to the Attendant Console, the call will
go to the originating station’s Attendant Console, as assigned via the Tenant parameter of the ATRK
command.
6. CLASS OF SERVICE-INDIVIDUAL [C-15]: Refer to the programming section. This feature affects the
construction of all classes of service.
Programming
STEP 1:ASYD - System Data 1, Index 8....