NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 547
Paging Access P-1
Interactions (cont’d)
5. For simple PAGING ACCESS [P-1], assignments in ASFC are not required. Refer directly to the other
Paging features, such as PAGING TRANSFER [P-10]. 
6. The Attendant can dial the PRIORITY PAGING [P-30] access code and release a station.
7. When disconnecting from a Paging trunk, the trunk becomes idle immediately. 
8. Paging is possible from a CONSULTATION HOLD [C-17]. Station A places Party B...

NEAX2400 IMX Feature Programming Manual
Page 548ND-70184 (E), Issue 3
P-2 Passing Dial Tone
P-2 Passing Dial Tone
General Description
This feature allows the Attendant to PASS DIAL TONE to a restricted user, enabling that user to place a call that
would normally be restricted.
Operating Procedure
1. Restricted user dials Attendant.
2. Attendant presses ANSWER or ATND key; tenant number, trunk route restriction class and telephone
number are displayed.
3. Obtain call details.
4. Dial central office access...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 549
Passing Dial Tone P-2
Interactions (cont’d)
2. The associated programming that should be examined is ATTENDANT CONSOLE [A-3], TOLL
DENIAL/TOLL DIVERSION [T-7], TOLL RESTRICTION-3/6 DIGIT [T-8], LEAST-COST
ROUTING-3/6 DIGIT [L-5], CLASS OF SERVICE-INDIVIDUAL [C-17], and the various trunk access
features. 
3. NIGHT CONNECTION FIXED/FLEXIBLE [N-1, 2]: The NIGHT CONNECTION FIXED/FLEXIBLE
stations cannot pass dial tone to another station....

NEAX2400 IMX Feature Programming Manual
Page 550ND-70184 (E), Issue 3
P-3 Power Failure Transfer
P-3 Power Failure Transfer
General Description
This feature provides for certain specified trunks to be automatically connected to designated stations in the event
of a loss of AC power. It is normally used when the system is not equipped with reserve power.
Station Application
Operation is automatic if there is loss of input power to the system.
Service Conditions
1. If the Central Office is wired ground...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 551
Pushbutton Calling P-4
P-4 Pushbutton Calling
General Description
This feature permits users to originate calls using pushbutton telephones and also allows Dterm stations the ability to
control external devices requiring DTMF signals to initiate or perform functions (Code-A-Phone, Conference Unit,
etc.).
Operating Procedure
1. The users press push-buttons corresponding to the desired numbers.
OR
2. After a connection is established...

NEAX2400 IMX Feature Programming Manual
Page 552ND-70184 (E), Issue 3
P-4 Pushbutton Calling
Programming (cont’d)
System Data 2, Index 2, Bit 0. Type of sender signal for station? 0/1: DP/PB. Assign as appropriate.
(This data will only be used if the ARTD data of a specific route is assigned as DP/PB.) 
System Data 3, Index 11. Normally assign data 00H for 128 milliseconds. 
STEP 2:ASDT - Assign D
term, single-line stations, a Telephone Equipment Class (TEC) of 2; pushbutton (PB),
TEC = 3, or Dial-Pulse/...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 553
Pushbutton Calling - Attendant Only P-5
P-5 Pushbutton Calling - Attendant Only
General Description
This feature permits an Attendant to place all calls over DTMF signaling lines from a pushbutton keypad on the
ATTENDANT CONSOLE [A-3].
Operating Procedure
Attendant presses the pushbutton keypad to dial.
Service Conditions
1. This feature requires that all Central Office trunks and TIE Trunk terminals accept pushbutton signaling...

NEAX2400 IMX Feature Programming Manual
Page 554ND-70184 (E), Issue 3
P-6 Pushbutton to Rotary Conversion
P-6  Pushbutton to Rotary Conversion
General Description
This feature allows DTMF telephones to be used when DTMF signaling is not provided or are not available from
the Central Office and/or TIE Line.
Operating Procedure
Users dial the desired telephone numbers.
Service Conditions
1. PUSHBUTTON TO ROTARY CONVERSION is software controlled on a per-trunk route basis.
2. See UNIVERSAL SENDER [U-3] for...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 555
Pushbutton to Rotary Conversion P-6
Programming (cont’d)
902-ORT 913-TCFT for ATT
903-IRT 915- Night ATT
905-Sender 916-MFCR 
909-DCFT 917-MFCS
919 to 926-Modem
TK: Trunk Number
TN: Tenant Number 
RSC: Route Restriction Class
SFC: Service Feature Class
STEP 4:ARTD - Outgoing routes must be assigned as DP or DP/PB. Flag CDN 2:ONSG as data “1”, DP or
data “3”, DP/PB.
FCCS Programming 
This data setting describes only the additional or...

NEAX2400 IMX Feature Programming Manual
Page 556ND-70184 (E), Issue 3
P-7 Peg Count
P-7 Peg Count
General Description
This service feature permits traffic studies and traffic analysis information to be accessed from the
MAINTENANCE ADMINISTRATION TERMINAL (MAT) [M-18] and printed out.
Operating Procedure
Refer to the NEAX2400 IMX System Operations and Maintenance Manual.
Service Conditions
1. All information required for this feature is registered at the MAT.
2. The following information is available:...