NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 517
Non-delay Operation N-3
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
STEP 1:ARSCN - Construct a Route Restriction Class (RSC) that will allow outgoing access to...

NEAX2400 IMX Feature Programming Manual
Page 518ND-70184 (E), Issue 3
N-7D Non-exclusive Hold - Dterm
N-7D Non-exclusive Hold - Dterm
General Description
This feature allows a Dterm user to place a call on Hold, from which it can be retrieved by any Dterm station that
displays the held line.
Operating Procedure
1. While a call is in progress, press the HOLD key.
2. To retrieve a held call; press the held line.
Service Conditions
1. Any Dterm station displaying the held line can seize the held call.
2....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 519
Non-exclusive Hold - DtermN-7D
Service Conditions (cont’d)
d.) when a station has a path to a station that has a station held by MUSIC ON HOLD [M-7] for
CONSULTATION HOLD - ALL CALLS [C-17] or CONSULTATION HOLD - ALL CALLS
D
term [C-17D]:
e.) when a station has a path to two trunks at one time for THREE-WAY CALLING [T-2] or
THREE-WAY CALLING - D
term [T-2D]:
f.) when a station has a path to a trunk and a station at one time for...

NEAX2400 IMX Feature Programming Manual
Page 520ND-70184 (E), Issue 3
N-8D Non-square Line Assignment - Dterm
N-8D Non-square Line Assignment - Dterm
General Description
This service feature allows the line function buttons on the Dterm set to be freely assigned as line keys or as service
feature keys. These assignments are done on a per-station basis.
Operating Procedure
Key designations are assigned via the Maintenance Administration Terminal (MAT) [M-18].
Service Conditions
Programming one feature to...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 521
Night Connection Outside - System N-17
N-17  Night Connection Outside - System
General Description
This is a night transfer service on a system basis, enabling a ring-down or LDN call to be transferred to a preselected
station outside the NEAX2400 IMX when night mode has been set.
Operating Procedure
1. The Attendant sets night mode. (Night Key, PB, Handset Extraction, MB).
2. A ring-down or LDN call terminates from a trunk.
3. The...

NEAX2400 IMX Feature Programming Manual
Page 522ND-70184 (E), Issue 3
N-28 Name Display - System
N-28  Name Display - System
General Description
This feature allows a Dterm with LCD display to indicate the user information corresponding to the calling telephone
number while engaged in STATION-TO-STATION CALLING [S-11].
Operating Procedure
1. When originating a station-to-station call:
Note:
The user information on the LCD flashes until the call is answered.
2. When a station call has been transferred to...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 523
Name Display - System N-28
Operating Procedure (cont’d)
 
Note:
The user information on the LCD flashes until the call is answered.
3. When both the calling/called station are released from a station-to-station call, the LCD of the calling/
called station displays:
Service Conditions
1. This service is available when either of the calling/called station is a Dterm, with an LCD display.
2. By this service, ASCII character data can be...

NEAX2400 IMX Feature Programming Manual
Page 524ND-70184 (E), Issue 3
N-28 Name Display - System
Service Conditions (cont’d)
b.) User information is displayed on the middle line of LCD, beginning on the 9th segment from the
left. When the information is less than 16 digits, the unused segments are left blank. The
information cannot be displayed on the upper line of LCD.
7. 8-digit display of D
term Series E:
a.) User information is displayed on the upper line of LCD, beginning on the 17th segment from...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 525
On-line Maintenance O-1
O-1 On-line Maintenance
General Description
This service feature permits maintenance routines to be performed on the NEAX2400 IMX without affecting normal
system operation.
Operating Procedure
Refer to the NEAX2400 IMX Office Data Specification.
Service Conditions
1. The following maintenance functions may be performed while the system is ON-LINE:
a.) Generic Program and Operating Memory testing
b.) Fault...

NEAX2400 IMX Feature Programming Manual
Page 526ND-70184 (E), Issue 3
O-2 Outgoing Trunk Queuing
O-2 Outgoing Trunk Queuing
General Description
This feature allows a user to dial a specified access code and enter a first-in, first-out queue, when encountering a
trunk busy signal. As soon as an OUTGOING TRUNK becomes available, stations in the queue will be called back
on a first-come, first-served basis.
Operating Procedure
When LEAST COST ROUTING - 3/6-DIGIT [L-5] is not provided: 
1. Dial the trunk...